修理を始めるには

修理する権利

ストア

iMac Intel 27" EMC 2546 Heat Sink Replacement

作成者： Andrew Optimus Goldheart (そして 5 人のその他投稿者)
  • コメント: 0
  • お気に入り: 1

難易度

普通

手順

6

所要時間

必要時間を提案??

セクション

1

フラグ

1

Prerequisite Only

必要条件のみ

このガイドは他のガイドにとって唯一の必要条件であることに注意してください。

はじめに

prerequisite for logic board, heat sink, and CPU

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Remove the four 7.5 mm T8 screws from behind the GPU on the logic board. These screws are set inside large, spring-loaded Phillips #2 screws. To prevent the larger screws from spinning when you loosen the T8 screws, hold them with a fingertip or Phillips #2 screwdriver. These screws are set inside large, spring-loaded Phillips #2 screws. To prevent the larger screws from spinning when you loosen the T8 screws, hold them with a fingertip or Phillips #2 screwdriver.

    • Remove the four 7.5 mm T8 screws from behind the GPU on the logic board.

    • These screws are set inside large, spring-loaded Phillips #2 screws. To prevent the larger screws from spinning when you loosen the T8 screws, hold them with a fingertip or Phillips #2 screwdriver.

    翻訳

  2. Remove the bracket from behind the GPU heat sink.

    • Remove the bracket from behind the GPU heat sink.

    翻訳

  3. The Essential Toolkit

    コンパクト版iFixitキットの中で最も利便性の高いツール

    ショップを見る

    The Essential Toolkit

    コンパクト版iFixitキットの中で最も利便性の高いツール

    ショップを見る

  4. Remove four black stickers from the back of the CPU heat sink.

    • Remove four black stickers from the back of the CPU heat sink.

    翻訳

  5. Remove four 12.3 mm T10 screws from the back of the CPU heat sink.

    • Remove four 12.3 mm T10 screws from the back of the CPU heat sink.

    翻訳

  6. Remove the spring plate from behind the CPU heat sink. Lift and remove the backing plate from behind the CPU heat sink. The backing plate has two posts that fit into alignment holes in the logic board. Lift and remove the backing plate from behind the CPU heat sink. The backing plate has two posts that fit into alignment holes in the logic board.

    • Remove the spring plate from behind the CPU heat sink.

    • Lift and remove the backing plate from behind the CPU heat sink. The backing plate has two posts that fit into alignment holes in the logic board.

    翻訳

  7. Lift the heat sink up from the logic board. The CPU will most likely stick to the heat sink, so be careful about where you put it down. The CPU will most likely stick to the heat sink, so be careful about where you put it down.

    • Lift the heat sink up from the logic board.

    • The CPU will most likely stick to the heat sink, so be careful about where you put it down.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

5他の投稿者と一緒に

Andrew Optimus Goldheart

メンバー登録日: 2009年10月17日

462,181 ポイント

410のガイドは作成済み

バッジ: 43

+40 個以上のバッジ

チーム

iFixit iFixit人のメンバー

Community

131 メンバー

13,474のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 150