キャンセル

iMac G5 17" Model A1144 IR Board Replacement

作成者： Walter Galan (そして 3 人のその他投稿者)

コメント: 3
お気に入り: 0

iMac G5 17" Model A1144 IR Board Replacement

難易度

普通

手順

13

所要時間

必要時間を提案??

はじめに

The ins and outs of replacing your IR board.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

手順1 Access Door

Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.
Loosen the two Phillips screws securing the access door to your iMac.
These screws are captive in the access door.

手順2

Remove the access door from your iMac.

Remove the access door from your iMac.

手順3 Front Bezel

Remove the three T8 Torx screws securing the front bezel to the rear panel.

Remove the three T8 Torx screws securing the front bezel to the rear panel.

手順4

Orient the iMac face-up, on its backside.

Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

Orient the iMac face-up, on its backside.
Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

手順5

While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

手順6

Re-orient your iMac so it sits upright on the stand.

Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

Push the card toward the top of the iMac to release the front bezel latch.

Re-orient your iMac so it sits upright on the stand.
Insert a plastic card up into the corner of the air vent slot at the top of the rear case.
Push the card toward the top of the iMac to release the front bezel latch.
Pull the front bezel away from the rear case.
Repeat this process for the other side of the front bezel.
It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.
If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

手順7

Lay your iMac stand-side down on a table.

Lay your iMac stand-side down on a table.
Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.
Lay the front bezel above the rest of the iMac.

手順8

If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

手順9

Disconnect both the camera and microphone cables.

Disconnect both the camera and microphone cables.

Disconnect both the camera and microphone cables.

手順10 IR Board

Peel back the aluminum EMI shield up off the lower three edges of the rear case.

Peel back the aluminum EMI shield up off the lower three edges of the rear case.
It is not necessary to peel the EMI shield off the display.
We found it helpful to tape the EMI shield up against the display to keep it out of the way.

手順11

Remove the single T6 Torx screw securing the IR board bracket to the logic board.

Remove the single T6 Torx screw securing the IR board bracket to the logic board.
The IR board and cable finger are now free from the logic board and may fall.

手順12

Pull the IR Board cable connector straight away from its socket on the IR board.

Pull the IR Board cable connector straight away from its socket on the IR board.

手順13

Transfer the two T6 Torx screws and the IR bracket to your new IR board.

Transfer the two T6 Torx screws and the IR bracket to your new IR board.

まとめ

To reassemble your device, follow these instructions in reverse order.

作成者

3他の投稿者と一緒に

Walter Galan

592,978 ポイント

1,203のガイドは作成済み

+50 個以上のバッジ

0コメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 3

今までの合計 4,029