メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

iMac G5 17" Model A1144 Camera Board Replacement

作成者： Andrew Bookholt (そして 2 人のその他投稿者)
  • コメント: 3
  • お気に入り: 0

難易度

普通

手順

12

所要時間

必要時間を提案??

セクション

3

フラグ

0

はじめに

iSight not working? Replace your camera board.

ツール

これらのツールを購入する

パーツ

パーツは必要ありません。

  1. Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Loosen the two Phillips screws securing the access door to your iMac.

    • These screws are captive in the access door.

    翻訳

  2. Remove the access door from your iMac.

    • Remove the access door from your iMac.

    翻訳

  3. Remove the three T8 Torx screws securing the front bezel to the rear panel.

    • Remove the three T8 Torx screws securing the front bezel to the rear panel.

    翻訳

  4. Orient the iMac face-up, on its backside. Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    • Orient the iMac face-up, on its backside.

    • Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    翻訳

  5. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する

  6. While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    • While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    翻訳

  7. Re-orient your iMac so it sits upright on the stand. Insert a plastic card up into the corner of the air vent slot at the top of the rear case. Push the card toward the top of the iMac to release the front bezel latch.

    • Re-orient your iMac so it sits upright on the stand.

    • Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

    • Push the card toward the top of the iMac to release the front bezel latch.

    • Pull the front bezel away from the rear case.

    • Repeat this process for the other side of the front bezel.

    • It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.

    • If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

    翻訳

  8. Lay your iMac stand-side down on a table.

    • Lay your iMac stand-side down on a table.

    • Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.

    • Lay the front bezel above the rest of the iMac.

    翻訳

  9. If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    • If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    翻訳

  10. Disconnect both the camera and microphone cables. Disconnect both the camera and microphone cables.

    • Disconnect both the camera and microphone cables.

    翻訳

  11. Lay the bezel front side down on a table.

    • Lay the bezel front side down on a table.

    • If necessary, peel back the tape covering the camera board.

    翻訳

  12. Remove the two T6 Torx screws securing the camera board to the front bezel.

    • Remove the two T6 Torx screws securing the camera board to the front bezel.

    翻訳

  13. Lift the camera board out from the front bezel.

    • Lift the camera board out from the front bezel.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

作成者

2他の投稿者と一緒に

Andrew Bookholt

513,461 ポイント

618のガイドは作成済み

バッジ: 47

+44 個以上のバッジ

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 1

過去 30 日: 2

今までの合計 4,638