メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

iMac G5 17" Model A1144 AirPort/Bluetooth Board Replacement

作成者： Walter Galan (そして 3 人のその他投稿者)
  • コメント: 3
  • お気に入り: 0
  • 完了: 2

難易度

普通

手順

13

所要時間

必要時間を提案??

セクション

3

フラグ

0

はじめに

Regain wireless connectivity by replacing your broken AirPort/Bluetooth board.

ツール

これらのツールを購入する

パーツ

  1. Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Before you work on the computer, unplug the computer and press the power button for 20-30 seconds to drain the stored energy in the power supply.

    • Loosen the two Phillips screws securing the access door to your iMac.

    • These screws are captive in the access door.

    翻訳

  2. Remove the access door from your iMac.

    • Remove the access door from your iMac.

    翻訳

  3. Remove the three T8 Torx screws securing the front bezel to the rear panel.

    • Remove the three T8 Torx screws securing the front bezel to the rear panel.

    翻訳

  4. Orient the iMac face-up, on its backside. Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    • Orient the iMac face-up, on its backside.

    • Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.

    翻訳

  5. While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    • While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.

    翻訳

  6. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now

  7. Re-orient your iMac so it sits upright on the stand. Insert a plastic card up into the corner of the air vent slot at the top of the rear case. Push the card toward the top of the iMac to release the front bezel latch.

    • Re-orient your iMac so it sits upright on the stand.

    • Insert a plastic card up into the corner of the air vent slot at the top of the rear case.

    • Push the card toward the top of the iMac to release the front bezel latch.

    • Pull the front bezel away from the rear case.

    • Repeat this process for the other side of the front bezel.

    • It may be necessary to apply several layers of duct tape to the top of the access card to aid in releasing the latches.

    • If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.

    翻訳

  8. Lay your iMac stand-side down on a table.

    • Lay your iMac stand-side down on a table.

    • Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.

    • Lay the front bezel above the rest of the iMac.

    翻訳

  9. If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    • If necessary, remove the piece of kapton tape wrapped around the microphone and camera cables.

    翻訳

  10. Disconnect both the camera and microphone cables. Disconnect both the camera and microphone cables.

    • Disconnect both the camera and microphone cables.

    翻訳

  11. Peel back the aluminum EMI shield up off the lower three edges of the rear case.

    • Peel back the aluminum EMI shield up off the lower three edges of the rear case.

    • It is not necessary to peel the EMI shield off the display.

    • We found it helpful to tape the EMI shield up against the display to keep it out of the way.

    翻訳

  12. Remove the single T10 Torx screw securing the right speaker to the rear case. Pull the rear speaker out of the rear case, and move it out of the way.

    • Remove the single T10 Torx screw securing the right speaker to the rear case.

    • Pull the rear speaker out of the rear case, and move it out of the way.

    • It is not necessary to disconnect the right speaker.

    翻訳

  13. Remove the two T6 Torx screws securing the AirPort/Bluetooth board to the logic board. Lift the AirPort/Bluetooth board up from its left edge to separate it from its socket on the logic board.

    • Remove the two T6 Torx screws securing the AirPort/Bluetooth board to the logic board.

    • Lift the AirPort/Bluetooth board up from its left edge to separate it from its socket on the logic board.

    • Lift the AirPort/Bluetooth board from its left edge only. Trying to lift from its right edge may break the socket off the logic board.

    翻訳

  14. Use the flat end of a spudger to pry the AirPort and Bluetooth antenna connectors up off the AirPort/Bluetooth board. Use the flat end of a spudger to pry the AirPort and Bluetooth antenna connectors up off the AirPort/Bluetooth board.

    • Use the flat end of a spudger to pry the AirPort and Bluetooth antenna connectors up off the AirPort/Bluetooth board.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

3他の投稿者と一緒に

Walter Galan

595,904 ポイント

1,203のガイドは作成済み

バッジ: 53

+50 個以上のバッジ

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 7,582