メインコンテンツにスキップ

この翻訳は、ソースガイドの最新の更新を反映していない可能性があります。 翻訳の更新に協力してください。 または ソースガイドを参照してください

iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換

必要な工具と部品

  1. iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 1、 1の画像 1
    • コインを使って、バッテリーロッキングネジを90度時計回りに回転させます。

  2. iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 2、 1の画像 1
    • コンピュータからバッテリーを持ち上げます。

  3. この手順は未翻訳です。 翻訳を手伝う。

    iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換, リアディスプレイベゼル: 手順 3、 2の画像 1 iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換, リアディスプレイベゼル: 手順 3、 2の画像 2
    • Use a 1.5mm hex screwdriver to remove the two hex screws on either side of the display (four screws total).

    • If you don't have a 1.5mm hex driver, you can probably get these screws out with a T6 Torx screwdriver. However, if you use a T6 Torx driver you'll be more likely to strip the screws.

  4. この手順は未翻訳です。 翻訳を手伝う。

    iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 4、 2の画像 1 iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 4、 2の画像 2
    • Insert the flat end of a spudger perpendicular to the face of the display into the gap between the front and rear bezels near the upper left corner of the display.

    • Rotate the spudger away from the display to pry the rear bezel off the front bezel.

  5. この手順は未翻訳です。 翻訳を手伝う。

    iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 5、 1の画像 1
    • Run your spudger along the top edge of the front display bezel to evenly separate the two bezels.

  6. この手順は未翻訳です。 翻訳を手伝う。

    iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 6、 2の画像 1 iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 6、 2の画像 2
    • Working down from the upper left corner, use the flat end of a spudger to pry the rear bezel away from the left edge of the display.

  7. この手順は未翻訳です。 翻訳を手伝う。

    iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 7、 1の画像 1
    • Use the flat end of a spudger to pry the rear bezel away from the right edge of the display.

    • If necessary, pry along the bottom edge of the rear bezel to separate it from the display assembly.

  8. iBook G4 12インチ 800 MHz-1.2 GHzのリアディスプレイベゼルの交換: 手順 8、 1の画像 1
    • ディスプレイアセンブリからリアベゼルを持ち上げます。

終わりに

デバイスを再度組み立てるには、この説明書の逆の順番で組み立ててください。

2 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

en jp

50%

railgunさんは世界中で修理する私たちを助けてくれています! あなたも貢献してみませんか?
翻訳を始める ›

作成者

5人の作成者と共同で作成されました。

Andrew Bookholt

585,718 ポイント

619のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 6

今までの合計 4,147