メインコンテンツにスキップ

この翻訳は、ソースガイドの最新の更新を反映していない可能性があります。 翻訳の更新に協力してください。 または ソースガイドを参照してください

必要な工具と部品

  1. : 手順 1、 1の画像 1
    • コインを使って、バッテリーロッキングネジを90度時計回りに回転させます。

  2. : 手順 2、 1の画像 1
    • コンピュータからバッテリーを持ち上げます。

  3. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 3、 1の画像 1
    • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.

    • If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw 180 degrees in either direction and try again.

    • Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.

  4. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 4、 1の画像 1
    • If the computer has an AirPort card installed, follow the next three steps to remove it.

    • Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.

  5. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 5、 1の画像 1
    • Grasp the clear plastic tab on the AirPort card and pull toward the display.

  6. : 手順 6、 1の画像 1
    • AirPortカードを片手で掴み、もう一方の手を使って、アンテナケーブルを取り外します。

  7. : 手順 7、 1の画像 1
    • RAMシールドに留められたシルバーのプラスネジを4本外します。

  8. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 8、 1の画像 1
    • Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.

  9. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 9、 1の画像 1
    • Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.

    • Make sure that you reconnect the keyboard cable before replacing the RAM shield.

  10. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 10、 1の画像 1
    • Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.

  11. : 手順 11、 1の画像 1
    • コネクタからチップをまっすぐ引き抜きます。

ゴール

38 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

en jp

16%

railgunさんは世界中で修理する私たちを助けてくれています! あなたも貢献してみませんか?
翻訳を始める ›

作成者

7人の作成者と共同で作成されました。

iRobot

メンバー登録日: 09/24/09

1 ポイント

636のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 13

今までの合計 60,008