はじめに

Replacing a defective fan is pretty easy and will keep your laptop running cool.

Use a coin to rotate the battery locking screw 90 degrees clockwise.
  • Use a coin to rotate the battery locking screw 90 degrees clockwise.

  • Lift the battery out of the computer.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound out port.
  • Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound out port.

isn’t this step out of order? It belongs much later I think

panakabear - 返信

Remove the three 5.2 mm newly-revealed Phillips screws.
  • Remove the three 5.2 mm newly-revealed Phillips screws.

Screw sizes are 2.5mm x 6mm flat low profile head or cheese head.

XnriquX - 返信

this should be after step 12 no?

panakabear - 返信

Use a pin (or anything you like) to remove the three rubber feet from the lower case.
  • Use a pin (or anything you like) to remove the three rubber feet from the lower case.

コメントを追加する

Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
  • Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.

コメントを追加する

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove the one 10 mm and two 20 mm hex screws using a 2mm hex. Alternatively, a T8 Torx screwdriver key will do.
  • Remove the one 10 mm and two 20 mm hex screws using a 2mm hex. Alternatively, a T8 Torx screwdriver key will do.

FYI, the two screws at the top of this picture are longer than the one in the middle of the case. Don't mix them up!

JuciusMaximus - 返信

Top screws are 20 mm, middle one is 10 mm. These have thread lock.

commenter - 返信

The 3 long screws (not the ones under the rubber feet) are 2.5mm x 20mm metric. Head style is cheese head. i found replacements for these at ACE hardware, for about $0.08 each in a flat head drive style which IMO are better than the hex style that can easily be stripped.

XnriquX - 返信

I'm using a T9 here as my T8 is way too small.

MN73 - 返信

Remove the two 4.2 mm Phillips screws on either side of the battery contacts.
  • Remove the two 4.2 mm Phillips screws on either side of the battery contacts.

コメントを追加する

Breathe deeply. Trying times are ahead, but we promise the lower case does come off.
  • Breathe deeply. Trying times are ahead, but we promise the lower case does come off.

  • Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.

コメントを追加する

There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
  • There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.

If your iBook's been opened many times (Like mine has been) then this piece may be broken.

If it's cracked down the middle or a little off, what you'll want to do is use your bent paperclip from a few steps later (or another screwdriver) and pull the second piece away from the shell when you start lifting. should pull right out

Christian Wacker - 返信

Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
  • Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.

コメントを追加する

Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).
  • Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).

You might wanna use your spudger to pry up those back tabs to. You might break the bottom case just wiggling around waiting for it to pop loose.

neato - 返信

The orange screw on my machine has no head on it and is simply a flat surface. There is no way to remove it and consequently I completely trashed my unit attempting to remove the top cover.

There went a few bucks all for nothing as I had a spare HD sitting here ready to put in!

Calum - 返信

Be aware that you may need to use a spudger at the front of the computer to separate the metal shield from the bottom case.

michael leahy - 返信

Remove the small greasy springs with white plastic caps from either side of the battery contacts.
  • Remove the small greasy springs with white plastic caps from either side of the battery contacts.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Remove the five 5.8 mm  Phillips screws from the bottom shield.
  • Remove the five 5.8 mm Phillips screws from the bottom shield.

  • Peel back the yellow tape and foil shielding outlined in the image.

Upper left screw is 4.5 mm and has smaller head. The other four are 6 mm.

commenter - 返信

Don't peel back the long foil shielding pictured top right! It should stay attached to the bottom shield that you are removing.

neato - 返信

Quote from commenter:

Upper left screw is 4.5 mm and has smaller head. The other four are 6 mm.

All of the five screws are the same 6 mm in length (iBook G3 600 MHz)

florguh - 返信

Lift the bottom shield off.
  • Lift the bottom shield off.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Remove the single Phillips screw on the left side of the fan (there may be two screws).
  • Remove the single Phillips screw on the left side of the fan (there may be two screws).

  • Lift the fan out of its housing and disconnect it from the logic board.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

5 の人々がこのガイドを完成させました。

添付文書

iRobot

メンバー登録日: 2009年09月24日

1 ポイント

750のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 5

今までの合計 8,201