メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

  1. この手順は未翻訳です。 翻訳を手伝う。

    Use a coin to rotate the battery locking screw 90 degrees clockwise.
    • Use a coin to rotate the battery locking screw 90 degrees clockwise.

    • Lift the battery out of the computer.

  2. この手順は未翻訳です。 翻訳を手伝う。

    Your laptop should look approximately like this.
    • Your laptop should look approximately like this.

  3. この手順は未翻訳です。 翻訳を手伝う。

    Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound out port.
    • Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound out port.

  4. 目で確認できるようになった5.2mmプラスネジを3本外します。
    • 目で確認できるようになった5.2mmプラスネジを3本外します。

  5. この手順は未翻訳です。 翻訳を手伝う。

    Use a pin (or anything you like) to remove the three rubber feet from the lower case.
    • Use a pin (or anything you like) to remove the three rubber feet from the lower case.

  6. スパッジャーや小サイズのマイナスドライバーを使って、ゴム製バンパーを搭載している3つのメタルリングを持ち上げます。
    • スパッジャーや小サイズのマイナスドライバーを使って、ゴム製バンパーを搭載している3つのメタルリングを持ち上げます。

  7. 今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る

    今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る
  8. この手順は未翻訳です。 翻訳を手伝う。

    Remove the one 10 mm and two 20 mm hex screws using a 2mm hex. Alternatively, a T8 Torx screwdriver key will do.
    • Remove the one 10 mm and two 20 mm hex screws using a 2mm hex. Alternatively, a T8 Torx screwdriver key will do.

  9. この手順は未翻訳です。 翻訳を手伝う。

    Remove the two 4.2 mm Phillips screws on either side of the battery contacts.
    • Remove the two 4.2 mm Phillips screws on either side of the battery contacts.

  10. この手順は未翻訳です。 翻訳を手伝う。

    Breathe deeply. Trying times are ahead, but we promise the lower case does come off.
    • Breathe deeply. Trying times are ahead, but we promise the lower case does come off.

    • Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.

  11. この手順は未翻訳です。 翻訳を手伝う。

    There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
    • There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.

  12. この手順は未翻訳です。 翻訳を手伝う。

    Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
    • Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.

  13. この手順は未翻訳です。 翻訳を手伝う。

    Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).
    • Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).

  14. この手順は未翻訳です。 翻訳を手伝う。

    Remove the small greasy springs with white plastic caps from either side of the battery contacts.
    • Remove the small greasy springs with white plastic caps from either side of the battery contacts.

  15. この手順は未翻訳です。 翻訳を手伝う。

    Your laptop should look approximately like this.
    • Your laptop should look approximately like this.

  16. この手順は未翻訳です。 翻訳を手伝う。

    Remove the five 5.8 mm  Phillips screws from the bottom shield.
    • Remove the five 5.8 mm Phillips screws from the bottom shield.

    • Peel back the yellow tape and foil shielding outlined in the image.

  17. この手順は未翻訳です。 翻訳を手伝う。

    Lift the bottom shield off.
    • Lift the bottom shield off.

ゴール

11 の人々がこのガイドを完成させました。

添付文書

iRobot

メンバー登録日: 2009年09月24日

1 ポイント

648のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 7

今までの合計 7,876