はじめに

Stop holding your Xbox 360 wireless controller together with duct tape. Use this guide to replace your old broken rear case.

Depress the battery release button on the top of the controller.
  • Depress the battery release button on the top of the controller.

  • Remove the battery holder from the controller.

  • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

コメントを追加する

  • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

  • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

コメントを追加する

  • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

Any recommendation on which set of Security Torx tools to use? I've already purchased 2 kits, one of those being sold as "Xbox controller tools" but the diameter of the head does not fit the hole on the controller and that's critical for the 2 screws on the bottom. The tools must obviously be thinner in diameter and long enough to get there.

Arnie - 返信

How to open an XBOX 360 controller without a special screwdriver. http://www.instructables.com/id/How-to-o... Works perfectly.

Louis - 返信

A lot of thanks for your comment. It's very usefull

Echedey -

I picked up a handy torx key set from Auto Zone. Was about $10, no lose driver bits. has both sizes you need to repair the controller and the console. Here's the link:

http://www.autozone.com/autozone/accesso...

FierDancr - 返信

It doesn't really matter which set of bits you by or what brand makes them, Torx bits (and the security versions of them) are generic & come in standardized sizes. You do not need a special "xbox" tool kit, you just need a size 8 torx security bit, no matter what brand makes the bit/kit. Those types of "specialty kits" are usually just collections of generic bits that you can buy at a hardware store in a regular bit set. The difference is that a general bit set will have bits for screws that a specific item doesn't have in it, whereas a specialty kit will only include bits for the types & sizes of fasteners used in the specified item.

BTW, with the smaller sizes of torx security bits you can try breaking off the little post in the middle with needlenose pliers or something else that can fit in the there. Even if the post doesn't break off cleanly, it's usually short enough to fit a regular (non security) torx bit in the slot.

Nerfbomb - 返信

  • Insert a Spudger between the front and rear cases along the left edge of the controller.

  • Rotate the spudger toward the front of the controller, prying the two cases apart.

  • Rotate the spudger toward the front of the controller, prying the two cases apart.

コメントを追加する

  • Insert a spudger between the front and rear cases, near the headphone jack.

  • Rotate the spudger toward the front of the controller to pry the two cases apart.

コメントを追加する

  • Grasp the controller by the battery compartment and the headphone jack.

  • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

  • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

20 の人々がこのガイドを完成させました。

Brett Hartt

メンバー登録日: 2010年04月12日

107,906 ポイント

138のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

111 メンバー

6,679のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 19

過去 30 日: 78

今までの合計 18,095