HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement

はじめに

This guide will instruct the user on how to remove and replace the viewfinder mirror and lens on the HP Photosmart 935 Viewfinder Digital Camera. The following instructions can be used as an installation guide for a new viewfinder mirror and lens.

必要な工具と部品

手順1 Batteries

HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement, Batteries: 手順 1、 2の画像 1

HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement, Batteries: 手順 1、 2の画像 2

Flip the camera over so the bottom of the camera is facing you.

編集

手順2

Turn the mode dial to the OFF position.

編集

手順3

Slide the bottom cover in the direction of the arrow to open it.

編集

手順4

Pull out the batteries.

編集

手順5 Plastic Casing

HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement, Plastic Casing: 手順 5、 1の画像 1

Use a Phillips #00 screwdriver to remove the two 4.7 mm screws in the bottom of the plastic casing.

編集

手順6

Remove the four 4.7 mm screws on the left side of the camera.

編集

手順7

Remove the four 4.7 mm screws on the opposite side of the camera.

編集

手順8

HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement: 手順 8、 3の画像 3

Use your thumbs to pry the case apart.
It is easiest to pry the case apart if you start at the bottom.
The case should come apart with minimal effort. If it doesn't, you can use a spudger or plastic opening tool to pry it open.

編集

手順9

This step requires a significant amount of force.
Pull the bottom half of the inner camera out of the case by half an inch. This may be difficult.

編集

手順10

While pulling the camera out of the case, note the small soft plastic cover on the side. This cover will detach from the rest of the device.
Once the bottom of the inner camera is pulled out, pull the device out completely.
Use a firm grasp when removing the device from the case for stability and control.

編集

手順11 LCD Screen

HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement, LCD Screen: 手順 11、 1の画像 1

Orient the camera so that the LCD screen is facing you.
If case is still on, remove it by following the Plastic Casing Installation Guide found in the previous steps.
Removing the casing completely is crucial to completing this guide.

編集

手順12

Using a Phillips #00 remove the four 4.40 mm screws that secure the LCD screen to the frame.

編集

手順13

Allow the LCD screen to flip down. This will expose the electric strip that connects the screen to the camera.

編集

手順14

Look for where the yellow electric strip is attached to the camera. You will find a plastic grey bar and a white base holding this strip in place.
Push the grey bar away from the white base. This will release the yellow electric strip and free the LCD screen from the camera.

編集

手順15

Unplug the connected red and white wires. They will come out with the small white casing.

編集

手順16

Flip camera so that the lens is facing away from you. You should be looking at the LCD screen.

編集

手順17

Remove the bottom left LCD mounting frame screw. The screen should come loose after the screw is removed.
Remove the LCD screen from the camera. Make sure that the electric strip comes out with screen.

編集

手順18 Viewfinder Mirror and Lens

HP Photosmart 935 Viewfinder Digital Camera Mirror and Lens Replacement, Viewfinder Mirror and Lens: 手順 18、 1の画像 1

Using a Phillips #00 screwdriver, remove the two screws securing the electric strip casing on the back of the camera.

編集

手順19

On the top of the camera where the shutter button is located, remove the screws located near the speaker that secure the electric strip casing.

編集

手順20

Turn the camera over to the side that once housed the LCD screen. Locate the electric strip near the top of the camera.
Holding the camera securely, gently pull the end of the electric strip off of the back of the camera using a pair of tweezers.

編集

手順21

Ensure there are two ends of the electric strip detached from the camera.

編集

手順22

Using your fingers, fully detach the strip along with the casing. Be careful not to rip or tear any part of the electric strip.
Do not break or remove the black wire. This will damage the camera.

編集

手順23

Orient the camera so that you are looking at the back of the camera. Directly above where the LCD screen was located, find the viewfinder cover clip.
Detach the clip with a pair of tweezers.
Push upwards and remove the viewfinder cover.