修理を始めるには コミュニティ ストア

VTech InnoTab 2s Power Connector Replacement

はじめに

This guide demonstrates how to remove and replace a VTech InnoTab 2s power connector in order to preserve the function of the device.

必要な工具と部品

  1. VTech InnoTab 2s Power Connector Replacement, Back Panel: 手順 1、 1の画像 1

    • Turn your device to where the back panel is facing you.

    編集

  2. VTech InnoTab 2s Power Connector Replacement: 手順 2、 2の画像 1 VTech InnoTab 2s Power Connector Replacement: 手順 2、 2の画像 2

    • Lift the Leg all the way up and twist the bottom to remove.

    • Once the bottom part pops out the whole leg should just come off.

    • Remove any game cartridge from the device.

    編集

  3. VTech InnoTab 2s Power Connector Replacement: 手順 3、 3の画像 1 VTech InnoTab 2s Power Connector Replacement: 手順 3、 3の画像 2 VTech InnoTab 2s Power Connector Replacement: 手順 3、 3の画像 3

    • Remove all of the plastic tabs on the device. These are covering screws that will need to be removed.

    • These covers are made of hard plastic so they may be difficult to remove.

    • There is a special tab in the cartridge cover that is made of rubber, make sure to not break this tab.

    編集

  4. VTech InnoTab 2s Power Connector Replacement: 手順 4、 2の画像 1 VTech InnoTab 2s Power Connector Replacement: 手順 4、 2の画像 2

    • Remove all nine screws from the back of the device using a J0 bit.

    • Remove the small battery.

    編集

  6. VTech InnoTab 2s Power Connector Replacement: 手順 5、 2の画像 1 VTech InnoTab 2s Power Connector Replacement: 手順 5、 2の画像 2

    • Using a plastic opening tool, detach the backplate from the front piece.

    • Do not use excessive force. Double check that you removed all the screws if the panel is not coming off easily.

    • Once the backplate has been removed, you will have access to the circuit board.

    編集

  7. VTech InnoTab 2s Power Connector Replacement, Motherboard: 手順 6、 1の画像 1

    • First begin by removing the three cross-head screws using a J0 bit.

    編集

  8. VTech InnoTab 2s Power Connector Replacement: 手順 7、 1の画像 1

    • First remove the ribbon cables. There are two highlighted by the red squares

    • Do not apply too much pressure and make sure that the black plastic tabs are fully open before you pull the cable out.

    編集

  9. VTech InnoTab 2s Power Connector Replacement: 手順 8、 1の画像 1

    • Remove the camera from the assembly and put is a safe place so that it will not get damaged.

    編集

  10. VTech InnoTab 2s Power Connector Replacement: 手順 9、 1の画像 1

    • Remove the board from the main assembly.

    • Be careful not to pull too hard so that the cables aren't broken.

    編集

  11. VTech InnoTab 2s Power Connector Replacement: 手順 10、 1の画像 1

    • De-solder the points shown to fully remove the cables and free the board.

    • A soldering guide offered by IFIXIT can be found here Soldering Skills.

    編集

  12. VTech InnoTab 2s Power Connector Replacement, Power Connector: 手順 11、 1の画像 1

    • Use a soldering tool to desolder the two highlighted points.

    • A soldering guide offered by IFIXIT can be found here: Soldering Skills.

    編集

  13. VTech InnoTab 2s Power Connector Replacement: 手順 12、 1の画像 1

    • Use a screwdriver to remove the screw that is holding the power jack in place.

    • Now you have access to remove and replace the power jack.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

5人の作成者と共同で作成されました。

Esthevan Romeiro

メンバー登録日: 10/06/16

261 ポイント

4のガイドは作成済み

バッジ: 9

+6 個以上のバッジ

チーム

USF Tampa, Team 5-1, Lacy Fall 2016 USF Tampa, Team 5-1, Lacy Fall 2016人のメンバー

USFT-LACY-F16S5G1

4 メンバー

12のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 2

今までの合計 325