修理を始めるには コミュニティ ストア

Umbrella Stretcher to Rib Joint Repair

はじめに

A really windy day can break an umbrella. In some cases, a joint will break, disconnecting the stretcher from the rib. You will be using a needle and thread in order to replicate the function of the joint that held the stretcher and the rib together. In addition, this guide will also cover how to sew a small rip on the canopy.

必要な工具と部品

  1. Umbrella Stretcher to Rib Joint Repair, Umbrella Stretcher to Rib Joint Repair: 手順 1、 2の画像 1 Umbrella Stretcher to Rib Joint Repair, Umbrella Stretcher to Rib Joint Repair: 手順 1、 2の画像 2

    • Take the broken part of the stretcher to rib joint.

    • Realign it with the rib assembly.

    編集

  2. Umbrella Stretcher to Rib Joint Repair: 手順 2、 1の画像 1

    • Take the needle and carefully pass it through one of the holes as seen in the picture.

    • Then pull it back to the same side you went through.

    編集

  3. Umbrella Stretcher to Rib Joint Repair: 手順 3、 1の画像 1

    • Take the needle and pass it under the stretcher (not through the middle).

    編集

  5. Umbrella Stretcher to Rib Joint Repair: 手順 4、 1の画像 1

    • Position the needle so that it faces the second hole from the same side you just went through in step 3.

    • Take the needle and pass it through the second hole.

    • Then position the needle so that it faces the first hole from the same side you just went through.

    編集

  6. Umbrella Stretcher to Rib Joint Repair: 手順 5、 2の画像 1 Umbrella Stretcher to Rib Joint Repair: 手順 5、 2の画像 2

    • Repeat steps 2-4 until the two pieces are held tightly together.

    • Tie a knot to secure it.

    • Refer to step six if the rib punctured the canopy.

    編集

  7. Umbrella Stretcher to Rib Joint Repair: 手順 6、 2の画像 1 Umbrella Stretcher to Rib Joint Repair: 手順 6、 2の画像 2

    • It is easier to sew when the canopy is closed

    • Take the hole, hold each end and pull outward into a line.

    • Make sure that it is in line with the umbrella canopy seam.

    • Take the needle and thread and form a hemming stitch (see Step 7).

    編集

  8. Umbrella Stretcher to Rib Joint Repair: 手順 7、 3の画像 1 Umbrella Stretcher to Rib Joint Repair: 手順 7、 3の画像 2 Umbrella Stretcher to Rib Joint Repair: 手順 7、 3の画像 3

    • Begin with a threaded needle and start the stitch at one end of the hole and pull the needle all the way until just before the thread runs out.

    • Then loop back around and go through again.

    • Repeat until you reach the other end.

    • You can form the stitch multiple times to make it more secure.

    編集
終わりに

The umbrella is fixed now, you may now use the umbrella freely.

2 の人々がこのガイドを完成させました。

作成者

1人の作成者と共同作成されました。

Rodrigo Soliva

メンバー登録日: 10/26/17

182 ポイント

1ガイドが承認済み

バッジ: 5

+2 個以上のバッジ

チーム

DePaul University, Team S1-G8, Dush Fall 2017 DePaul University, Team S1-G8, Dush Fall 2017人のメンバー

DPU-DUSH-F17S1G8

2 メンバー

1のガイドは作成済み

2 件のコメント

I have a problem with the auto lock, it's a knight bridge umbrella, when i retract it, it doesn't lock in place, can it be fixed or replace the handle in case it's totally eroded?

kamec 01 - 返信

I have 2 umbrellas which have both snapped at the hole. Is there a way this technique or a version of it can be used to repair them?

Jenny - 返信

コメントを追加

統計データ:

過去 24時間: 6

過去 7 日: 38

過去 30 日: 161

今までの合計 11,474