パーツ

パーツは必要ありません。

Turn off the computer.
  • Turn off the computer.

  • Disconnect the charging cable from computer.

  • Failure to unplug the cable could result in electric shock.

  • Flip the computer upside down.

コメントを追加する

Slide latches labeled #1 and #2, located outside the battery cover, away from each other.
  • Slide latches labeled #1 and #2, located outside the battery cover, away from each other.

  • Latch #1 will click over and stay while latch #2 will have to be held for battery to release.

コメントを追加する

Gently lift and pull the battery out of the device.
  • Gently lift and pull the battery out of the device.

コメントを追加する

Use tweezers to remove rubber screw covers on 4 corners of frame around screen. Use tweezers to remove rubber screw covers on 4 corners of frame around screen.
  • Use tweezers to remove rubber screw covers on 4 corners of frame around screen.

コメントを追加する

Remove 4 Phillips 5.6 mm screws.
  • Remove 4 Phillips 5.6 mm screws.

コメントを追加する

Use flat side of spudger to pry the top and sides of the frame around screen. Use flat side of spudger to pry the top and sides of the frame around screen.
  • Use flat side of spudger to pry the top and sides of the frame around screen.

コメントを追加する

Turn device onto its screen side to access the bottom of hinge portion of the screen and push bottom piece of frame along device hinge until it loosens. Turn device onto its screen side to access the bottom of hinge portion of the screen and push bottom piece of frame along device hinge until it loosens.
  • Turn device onto its screen side to access the bottom of hinge portion of the screen and push bottom piece of frame along device hinge until it loosens.

コメントを追加する

Return device to upright position and gently pull frame away from screen. Return device to upright position and gently pull frame away from screen. Return device to upright position and gently pull frame away from screen.
  • Return device to upright position and gently pull frame away from screen.

コメントを追加する

Remove 2 Phillips 5.6 mm screws from below screen.
  • Remove 2 Phillips 5.6 mm screws from below screen.

コメントを追加する

Unplug pink and white monitor cable from bottom of screen. Unplug pink and white monitor cable from bottom of screen.
  • Unplug pink and white monitor cable from bottom of screen.

コメントを追加する

Remove 3 Phillips 3.2 mm screws from each side of the metal case around screen.
  • Remove 3 Phillips 3.2 mm screws from each side of the metal case around screen.

コメントを追加する

Pull the screen forward from the top out of the metal frame enough to see the back of the screen.
  • Pull the screen forward from the top out of the metal frame enough to see the back of the screen.

コメントを追加する

Hold the screen with one hand and gently remove the display cable from the back side of the screen. The display cable is typically glued or taped to the back of the screen. Take care to carefully lift the tape and slowly pull cable. To avoid damaging screen ribbon cable, use caution and be gentle. Do not yank or remove with force. Avoid bending the ribbon cable which can cause the wires inside it to snap and break.
  • Hold the screen with one hand and gently remove the display cable from the back side of the screen.

  • The display cable is typically glued or taped to the back of the screen. Take care to carefully lift the tape and slowly pull cable.

  • To avoid damaging screen ribbon cable, use caution and be gentle. Do not yank or remove with force. Avoid bending the ribbon cable which can cause the wires inside it to snap and break.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Marianne

メンバー登録日: 2014年09月08日

647 ポイント

6のガイドは作成済み

チーム

Pasco Hernando, Team 5-2, Prince Fall 2014 Pasco Hernando, Team 5-2, Prince Fall 2014人のメンバー

PHSC-PRINCE-F14S5G2

10 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 1

今までの合計 285