修理を始めるには 修理する権利 ストア

Toshiba Satellite A215-S7425 Optical Drive Replacement

作成者： Marianne (そして 5 人のその他投稿者)
  • コメント: 0
  • お気に入り: 2

難易度

簡単

手順

9

所要時間

5 - 10 分

セクション

3

フラグ

1

Better Introduction

より良い紹介部分

この紹介部分を完成し編集することでこのガイドを改良する

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Turn off the computer.

    • Turn off the computer.

    • Disconnect the charging cable from computer.

    • Failure to unplug the cable could result in electric shock.

    • Flip the computer upside down.

    編集

  2. Slide latches labeled #1 and #2, located outside the battery cover, away from each other.

    • Slide latches labeled #1 and #2, located outside the battery cover, away from each other.

    • Latch #1 will click over and stay while latch #2 will have to be held for battery to release.

    編集

  3. Gently lift and pull the battery out of the device.

    • Gently lift and pull the battery out of the device.

    編集

  5. Locate the RAM vented plastic cover in the center of the device.

    • Locate the RAM vented plastic cover in the center of the device.

    編集

  6. Loosen 1 Phillips 4.2 mm size captive screw and lift cover off device to expose 2 RAM sticks. Loosen 1 Phillips 4.2 mm size captive screw and lift cover off device to expose 2 RAM sticks.

    • Loosen 1 Phillips 4.2 mm size captive screw and lift cover off device to expose 2 RAM sticks.

    編集

  7. Locate 2 metal pinchers on either side of the 1st RAM stick. Use a finger from each hand to push the 2 pinchers simultaneously away from the stick of RAM and towards the exterior of the case. The RAM stick will automatically rise up. Gently pull out the RAM stick with one hand.

    • Locate 2 metal pinchers on either side of the 1st RAM stick.

    • Use a finger from each hand to push the 2 pinchers simultaneously away from the stick of RAM and towards the exterior of the case.

    • The RAM stick will automatically rise up. Gently pull out the RAM stick with one hand.

    • The use of a anti-static wrist strap while working with the RAM is advise to prevent electrostatic discharge(ESD) from damaging the RAM.

    編集

  8. To remove the 2nd RAM stick, repeat previous steps. You will be unable to remove 2nd RAM stick if the first one is not removed first. You will be unable to remove 2nd RAM stick if the first one is not removed first.

    • To remove the 2nd RAM stick, repeat previous steps.

    • You will be unable to remove 2nd RAM stick if the first one is not removed first.

    編集

  9. Locate and remove 1 Phillips 4.2 mm size screw along right side of RAM container.

    • Locate and remove 1 Phillips 4.2 mm size screw along right side of RAM container.

    • Tweezers may be needed to lift out the screw.

    編集

  10. Push down metal rod until optical drive pops out from its container on the side of the device. To avoid damage to your RAM, make sure RAM is removed and out of the way before beginning this step.

    • Push down metal rod until optical drive pops out from its container on the side of the device.

    • To avoid damage to your RAM, make sure RAM is removed and out of the way before beginning this step.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

5他の投稿者と一緒に

Marianne

メンバー登録日: 2014年09月08日

647 ポイント

6のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

Pasco Hernando, Team 5-2, Prince Fall 2014 Pasco Hernando, Team 5-2, Prince Fall 2014人のメンバー

PHSC-PRINCE-F14S5G2

10 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 266