TomTom Runner LCD Screen Replacement Guide

はじめに

If the screen appears undamaged on the outside, but the screen is still unresponsive to charging or pressing the buttons, then the screen may need to be replaced. Use this guide to learn how to replace the screen.

必要な工具と部品

手順1 Wristband

TomTom Runner LCD Screen Replacement Guide, Wristband: 手順 1、 1の画像 1

First, lift the bottom part of the band to start removing the wristband from the button area of the watch.

編集

手順2

Continue to lift up on the band until the screen of the watch becomes loose from the band.
You may need to apply a small amount of force downward on the face of the screen.
Continue to pull up on the wristband until it is completely off the watch.

編集

手順3 Back Panel

TomTom Runner LCD Screen Replacement Guide, Back Panel: 手順 3、 1の画像 1

Grab the watch once it is separated from the wristband.

編集

手順4

Flip over the watch and remove the four 3.0 mm Torx head screws with a T4 Torx head screwdriver.

編集

手順5

Remove the two 3.0 mm Torx screws from the front. Use a T4 Torx screwdriver to remove the screws.
The two 3.0 mm Torx screws are painted blue at the end. These screws have screw holders around them that will also need to be removed.
Unscrew the screws from the front of the watch casing and the screw holders fall out from the back of the watch casing.

編集

手順6

Gently pull the back panel away from the front panel.
Do not to pull too fast or too hard. There are red and black wires connected to the vibrator component that should not be ripped.

編集

手順7

Gently wiggle the black box vibrator component away from the back panel with your fingers or a Spudger tool.
Be gentle with the red and black wires. You do not want them to rip or pop out.
The vibrator component is the small black box with the silver metal part at end. The black box is glued down, so it will take a little force to free it and it will be sticky.

編集

手順8 Front Cover

TomTom Runner LCD Screen Replacement Guide, Front Cover: 手順 8、 2の画像 1

TomTom Runner LCD Screen Replacement Guide, Front Cover: 手順 8、 2の画像 2

Now lift the smaller square of copper off the Front Panel. Use the bent, metal precision tweezers and slide it under the smaller square of copper lining then gently lift it up.
You will need to be gentle and pull the copper slowly so that it does not rip.

編集

手順9

Use the bent, metal precision tweezers to remove the thin copper piece from large square silver piece in the Front Casing.
You will need to be gentle and pull the copper slowly so that it does not rip.

編集

手順10

Remove the two 2.0 mm Torx Head screws with the T5 Torx screwdriver.

編集

手順11

TomTom Runner LCD Screen Replacement Guide: 手順 11、 3の画像 3

Use your fingers to gently pull the whole green motherboard out of the Front Casing.
If you have trouble using your fingers, then use the black Spudger tool.

編集

手順12 LCD Screen

TomTom Runner LCD Screen Replacement Guide, LCD Screen: 手順 12、 1の画像 1

Grab the screen attached to the green motherboard.

編集

手順13

TomTom Runner LCD Screen Replacement Guide: 手順 13、 3の画像 3

Using the pointed end of the black Spudger tool, gently pry the motherboard away from the screen.
The motherboard and screen are very fragile, but the motherboard should pop right off.
Once you have the motherboard partially pried off, use your fingers to gently pop it out of the clear, plastic clips holding it in place.
Continue to pull the motherboard away from the screen to fully expose the white backing of the screen.

編集

手順14

TomTom Runner LCD Screen Replacement Guide: 手順 14、 3の画像 3

Once the white backing of the screen is exposed, carefully flip the two pieces, the motherboard and the screen, over while they are still connected.
Look for the small metal piece attached to the motherboard that is wrapped around the front of the screen.
Gently slide the screen under and back to free it from the metal piece.