メインコンテンツにスキップ

Tara Pump Rod Replacement

必要な工具と部品

  1. Tara Pump Rod Replacement, Handle: 手順 1、 1の画像 1
    • Before performing any repairs, perform a water test on the pump by raising and lowering the handle a full 40 strokes. A properly performing pump will yield greater than 10 liters.

    • Use a Tara tool to loosen the jam nuts on either side of the pump.

    • The bolts do not need to be loosened or removed, only the nuts need to be loosened.

  2. Tara Pump Rod Replacement: 手順 2、 3の画像 1 Tara Pump Rod Replacement: 手順 2、 3の画像 2 Tara Pump Rod Replacement: 手順 2、 3の画像 3
    • Unscrew the lock bolts about half an inch.

    • The bolts do not need to be removed from the base.

  3. Tara Pump Rod Replacement: 手順 3、 2の画像 1 Tara Pump Rod Replacement: 手順 3、 2の画像 2
    • Pull the plastic bushing and handle straight up out of the pump.

    • If the bushing doesn't come up, loosen the lock bolts further.

  4. Tara Pump Rod Replacement: 手順 4、 2の画像 1 Tara Pump Rod Replacement: 手順 4、 2の画像 2
    • Lift up the handle and riser main until the joint between the two is at a comfortable height to work on.

  5. Tara Pump Rod Replacement: 手順 5、 3の画像 1 Tara Pump Rod Replacement: 手順 5、 3の画像 2 Tara Pump Rod Replacement: 手順 5、 3の画像 3
    • Loosen the jam nut beneath the pump handle using the Tara tool.

  6. Tara Pump Rod Replacement: 手順 6、 2の画像 1 Tara Pump Rod Replacement: 手順 6、 2の画像 2
    • Unscrew the pump handle from the top of the riser main.

    • Make sure someone is tightly holding the lower portion of the riser main to prevent losing it down the well.

  7. Tara Pump Rod Replacement: 手順 7、 2の画像 1 Tara Pump Rod Replacement: 手順 7、 2の画像 2
    • Lift and remove the handle from the pump. Store the handle in a sanitary place to prevent contamination.

  8. Tara Pump Rod Replacement, Pump Rod: 手順 8、 3の画像 1 Tara Pump Rod Replacement, Pump Rod: 手順 8、 3の画像 2 Tara Pump Rod Replacement, Pump Rod: 手順 8、 3の画像 3
    • Screw the T-handle onto the top of the riser main.

  9. Tara Pump Rod Replacement: 手順 9、 2の画像 1 Tara Pump Rod Replacement: 手順 9、 2の画像 2
    • Tighten the jam nut up against the base of the T-handle.

  10. Tara Pump Rod Replacement: 手順 10、 3の画像 1 Tara Pump Rod Replacement: 手順 10、 3の画像 2 Tara Pump Rod Replacement: 手順 10、 3の画像 3
    • Use the T-handle to push the riser main back down into the well.

  11. Tara Pump Rod Replacement: 手順 11、 3の画像 1 Tara Pump Rod Replacement: 手順 11、 3の画像 2 Tara Pump Rod Replacement: 手順 11、 3の画像 3
    • Once the riser main hits the bottom, turn the T-handle while pushing down.

    • This will hook the foot valve onto the traveling valve, allowing you to pull the two out of the well together.

    • You should feel some resistance if the foot valve is successfully attached.

  12. Tara Pump Rod Replacement: 手順 12、 2の画像 1 Tara Pump Rod Replacement: 手順 12、 2の画像 2
    • Use the T-handle to pull the riser main straight up out of the well.

    • Take care to pull up slowly to ensure the foot valve does not get released from the hook at the end of the riser main.

  13. Tara Pump Rod Replacement: 手順 13、 2の画像 1 Tara Pump Rod Replacement: 手順 13、 2の画像 2
    • Continue pulling the riser main up from the well.

    • Pull the riser main until the base of the T-handle is at a comfortable height to work on.

  14. Tara Pump Rod Replacement: 手順 14、 3の画像 1 Tara Pump Rod Replacement: 手順 14、 3の画像 2 Tara Pump Rod Replacement: 手順 14、 3の画像 3
    • Loosen the jam nut from the base of the T-handle.

    • Unscrew the T-handle from the top of the riser main.

    • Remove the T-handle, making sure to hold the remaining end of the riser main to prevent dropping it down the well.

  15. Tara Pump Rod Replacement: 手順 15、 3の画像 1 Tara Pump Rod Replacement: 手順 15、 3の画像 2 Tara Pump Rod Replacement: 手順 15、 3の画像 3
    • Continue to pull the riser main out of the well.

  16. Tara Pump Rod Replacement: 手順 16、 3の画像 1 Tara Pump Rod Replacement: 手順 16、 3の画像 2 Tara Pump Rod Replacement: 手順 16、 3の画像 3
    • Keep pulling until the first joint is exposed.

    • Lift the joint up to a comfortable working height.

  17. Tara Pump Rod Replacement: 手順 17、 3の画像 1 Tara Pump Rod Replacement: 手順 17、 3の画像 2 Tara Pump Rod Replacement: 手順 17、 3の画像 3
    • Use two wrenches to loosen the top section of riser main from the lower section.

    • Unscrew the top section of the riser main.

    • Make sure someone is holding the remaining section of the riser main.

  18. Tara Pump Rod Replacement: 手順 18、 3の画像 1 Tara Pump Rod Replacement: 手順 18、 3の画像 2 Tara Pump Rod Replacement: 手順 18、 3の画像 3
    • Remove the top section of the riser main.

  19. Tara Pump Rod Replacement: 手順 19、 1の画像 1
    • Lay the first section of riser main in a sanitary place to prevent contamination.

    • Repeat the previous procedure to remove the remaining sections of the riser main from the well.

    • Lay each new piece in the order it was removed to aid in reassembly.

  20. Tara Pump Rod Replacement: 手順 20、 3の画像 1 Tara Pump Rod Replacement: 手順 20、 3の画像 2 Tara Pump Rod Replacement: 手順 20、 3の画像 3
    • The last section of riser main will have the traveling valve screwed on to the end, and the foot valve hooked onto the traveling valve.

    • Be careful not to allow the foot valve to release from the hook by pulling slowly on the riser main.

  21. Tara Pump Rod Replacement: 手順 21、 3の画像 1 Tara Pump Rod Replacement: 手順 21、 3の画像 2 Tara Pump Rod Replacement: 手順 21、 3の画像 3
    • Lift and twist the foot valve to unhook it from the traveling valve.

  22. Tara Pump Rod Replacement: 手順 22、 1の画像 1
    • Once the riser main and valves have been removed from the well, place a rag over the top to prevent accidentally dropping anything down the well.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

6人の作成者と共同で作成されました。

Sam Goldheart

メンバー登録日: 10/18/12

465,323 ポイント

538のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Staff

136 メンバー

16,579のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 1

今までの合計 382