メインコンテンツにスキップ

Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement

必要な工具と部品

  1. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement, Back Cover: 手順 1、 1の画像 1
    • Remove the four Torx T5 screws from the back panel.

  2. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 2、 1の画像 1
    • Wedge a spudger in between the front and back panel.

    • Apply leverage downwards to the spudger in order to remove the back panel.

  3. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement, Battery: 手順 3、 1の画像 1
    • Slide the battery out from under the brown wire-tape.

    • Be careful of the wires still connected to the other end of the battery. Do not pull or damage may occur.

  4. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 4、 1の画像 1
    • Slowly pull the white plug from its receptor. Grasp its sides firmly with a pair of tweezers and gently wiggle from side to side.

  5. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement, Motherboard: 手順 5、 1の画像 1
    • Unscrew the 2 Philips #00 screws on each end of the motherboard.

  6. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 6、 1の画像 1
    • Pull off the black memory card slot piece with tweezers.

  7. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 7、 1の画像 1
    • Unscrew the 2 Philips #00 screws on each side of the charging port.

  8. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 8、 2の画像 1 Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 8、 2の画像 2
    • Disconnect 2 brown wire-tape ends from each end of the motherboard. Gently pull straight out with tweezers.

  9. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 9、 1の画像 1
    • Pull the motherboard and screen component diagonally up and left away from the auxiliary port entrance to remove.

    • Glue connecting the auxiliary port to the casing may make it difficult to remove. Gently apply force as needed.

  10. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 10、 1の画像 1
    • Disconnect the 2 brown wire-tape ends from the left side of the battery slot on the motherboard using tweezers.

  11. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 11、 3の画像 1 Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 11、 3の画像 2 Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 11、 3の画像 3
    • Disconnect the large brown wire-tape from the motherboard.

    • Peel the black tape back from the wire-tape using tweezers.

    • Lift the black, hinged, plastic lock with tweezers to release the wire-tape.

    • The screen and motherboard components can now be separated from each other.

  12. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement, Touchscreen/Display: 手順 12、 1の画像 1
    • Unscrew the 2 Philips #00 screws from the bottom edge of the screen component.

  13. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 13、 1の画像 1
    • Take off the brown wire-tape from the small circuit board component.

    • Lift up so that the black plastic hinge piece swings open and the tape can be removed.

  14. Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 14、 3の画像 1 Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 14、 3の画像 2 Tapwave T2907US Zodiac 2 Touchscreen/Display Replacement: 手順 14、 3の画像 3
    • Warning: If you are too rough with the screwdriver, you can permanently damage the display.

    • Use a Slot SL1.5 screwdriver to pry the touchscreen shell from the display component using the 4 slots around the entire component

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

5人の作成者と共同で作成されました。

Daniel Wiseman

メンバー登録日: 01/20/12

133 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 10-33, Amido Winter 2012 Cal Poly, Team 10-33, Amido Winter 2012人のメンバー

CPSU-AMIDO-W12S10G33

4 メンバー

10のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 4

今までの合計 900