はじめに

Use this guide to replace the RAM.

DS412+ Open the front pannel
  • DS412+

  • Open the front pannel

コメントを追加する

Remove the hard disks
  • Remove the hard disks

コメントを追加する

Remove those 2 screws Remove those 2 screws
  • Remove those 2 screws

コメントを追加する

Locate those 2 tabs Lift them up off the metal brace
  • Locate those 2 tabs

  • Lift them up off the metal brace

This step could really use a better illustration of the removal technique. The plastic here is extremely stiff and it can be hard to bend it enough to move the tabs.

This is the best technique I found, that will avoid damaging the plastic facing of the case. I am using the iFixit photo as a guide. Take a flathead screwdriver and place it down within the DS412, head facing up. Stick the head in between the metal bar and the plastic casing, and at the midpoint between the two tabs. Apply gentle pressure.

Chris - 返信

Push the case away It should look like this
  • Push the case away

  • It should look like this

コメントを追加する

Lift the case up Remove the case
  • Lift the case up

  • Remove the case

コメントを追加する

Remove this screw Remove this screw
  • Remove this screw

コメントを追加する

Remove this screw
  • Remove this screw

コメントを追加する

Remove those 4 screws Remove those 4 screws
  • Remove those 4 screws

コメントを追加する

Pull the fan a little bit away Pull the fan a little bit away
  • Pull the fan a little bit away

コメントを追加する

Watch out for this plug Lift the metal bracket out
  • Watch out for this plug

  • Lift the metal bracket out

コメントを追加する

Remove the fan power cords Remove the fan power cords
  • Remove the fan power cords

コメントを追加する

Remove the circuit board
  • Remove the circuit board

コメントを追加する

Remove those 4 screws Remove those 4 screws
  • Remove those 4 screws

コメントを追加する

Lift out the circuit board
  • Lift out the circuit board

コメントを追加する

Pull these tabs and remove the ram Old and new Ram To reassemble your device, follow these instructions in reverse order.
  • Pull these tabs and remove the ram

  • Old and new Ram

  • To reassemble your device, follow these instructions in reverse order.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

20 の人々がこのガイドを完成させました。

gieljnssns

メンバー登録日: 2011年06月26日

591 ポイント

1ガイドが承認済み

Hi is it also possible with a Synology ds216play? Or is the RAM not modular in this Drives?

markusguenther30684 - 返信

Very nice guide. Thank you!

mbs - 返信

Thank you for the guide, just to ease it up a bit for everybody following, the best way to pull the two tabs from step 4 was to use small spoon (or anything metal) and use it as a crowbar from the inside (do not try to put force from the outer rim, but really from inside of the Synology itself (against the metal beam the tabs are holding to).

Ondrej Palat - 返信

Thank you very much.

Olivier Claude - 返信

did these steps and now my DS412+ won't boot anymore. just the blue power light for a few seconds, no hard drive or fan will turn on.

after putting the old RAM in the slot nothing changed. cannot find any error, how do I find out what's wrong here???

Andreas Hanny - 返信

Super facile, en 10 minutes même pas c'est fait !!

user0 - 返信

This guide was great. Thanks for posting it!

I upgrade to 2gb RAM last night with no problems. I used "Kingston Technology ValueRAM 2GB 1333MHz DDR3 Non-ECC CL9 SODIMM SR X16 Notebook and Portable Memory KVR13S9S6/2" from Amazon.

System is humming along nicely now.

Jeff Smith - 返信

Thank you for this guide.

I upgrade my RAM without any trouble.

The use of two tea spoon to lift the tab in step 4 is very useful.

Marc Jean - 返信

コメントを追加する

統計データを表示:

過去 24時間: 5

過去 7 日: 30

過去 30 日: 164

今までの合計 8,279