メインコンテンツにスキップ

はじめに

This guide will show you how to replace the gyroscope component of your SwagTron T1. This may be necessary if the self-balancing function of your hoverboard is not working correctly. Before attempting this replacement, recalibrate your SwagTron. If the problem persists, continue with this replacement. This replacement can be done for the gyroscope component on either side of your SwagTron T1.

パーツ

パーツは指定されていません。

  1. Ensure that the SwagTron is off.
    • Ensure that the SwagTron is off.

    • Turn the SwagTron upside down to see the underside.

  2. Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver. The screws are tightly in place. It will take effort to screw them out. The panel is still attached to the SwagTron by wires that go to the motherboard.
    • Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver.

    • The screws are tightly in place. It will take effort to screw them out.

    • The panel is still attached to the SwagTron by wires that go to the motherboard.

    • Carefully lift the panels off

  3. Follow the wires from the panels to the motherboard. You may need to cut any zip ties that are holding the wires together. There is one connection on the battery side and three on the other side that must be removed.
    • Follow the wires from the panels to the motherboard.

    • You may need to cut any zip ties that are holding the wires together.

    • There is one connection on the battery side and three on the other side that must be removed.

    • These connections may be difficult to remove. Try to securely press the connection and pull firmly.

    • Your back panels are now completely removed.

  4. Disconnect the gyroscope by disconnecting the wires attached to it. These wires are black, green, blue and red. Disconnect the gyroscope by disconnecting the wires attached to it. These wires are black, green, blue and red.
    • Disconnect the gyroscope by disconnecting the wires attached to it. These wires are black, green, blue and red.

  5. Using your Phillips #2 screwdriver, remove the four 8mm screws marked in red from the gyroscope.
    • Using your Phillips #2 screwdriver, remove the four 8mm screws marked in red from the gyroscope.

  6. Carefully remove the gyroscope component from the SwagTron. Carefully remove the gyroscope component from the SwagTron. Carefully remove the gyroscope component from the SwagTron.
    • Carefully remove the gyroscope component from the SwagTron.

終わりに

To reassemble your device, follow these instructions in reverse order.

8 の人々がこのガイドを完成させました。

Teagan Allen

メンバー登録日: 2017年04月18日

387 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team S17-G5, Banghart Spring 2017 Cal Poly, Team S17-G5, Banghart Spring 2017人のメンバー

CPSU-BANGHART-S17S17G5

4 メンバー

5のガイドは作成済み

4 件のコメント

I cannot find a Swagtron T1 replacement gyroscope anywhere on the internet. Any help would be extremely appreciated!! Thank you!

Gavin Hosler - 返信

Amazon.com Keyword: CertiCable

Jesse Griffis -

Where do you get the replacement?

Brittany Conner - 返信

Can’t find gyroscope for a t5 hover board please help.

jbswearingen70739 - 返信

コメントを追加

統計データを表示:

過去 24時間: 1

過去 7 日: 10

過去 30 日: 49

今までの合計 5,407