はじめに

If your sharpener is making a loud grinding noise or the electric motor is running but the cutter is not rotating, then follow these steps to replace the gears in your Staples 34462 Electric Pencil Sharpener.

  1. Pull out the shavings tray from the pencil sharpener.
    • Pull out the shavings tray from the pencil sharpener.

    • Beware of loose pencil shavings falling on your workspace.

  2. Turn the pencil sharpener on its side.
    • Turn the pencil sharpener on its side.

  3. Using a Phillips00 screwdriver, remove the two front 11.6mm screws.
    • Using a Phillips00 screwdriver, remove the two front 11.6mm screws.

    • Using the plastic opening tool, remove the back plastic feet.

    • After removing the back plastic feet, using a Phillips 00 screwdriver, remove the two back 11.6mm screws.

    • The hole is deeper than you may think. It may take some time to get the screwdriver to click in.

  4. Carefully pull apart the bottom panel from the top panel.
    • Carefully pull apart the bottom panel from the top panel.

    • Be careful not to pull too forcefully as the panels are connected by wires.

    • Beware of pencil shavings falling out onto your workspace.

  5. Free shipping on all orders over $100.00 or containing a Pro Tech Toolkit!

    当社のショップを閲覧する

    Ever fixed something? That’s Genius.

    Share your repair story with #ImAGenius

    We Are All Geniuses

    Share your repair story with #ImAGenius

  6. Using a Phillips00 screwdriver, remove two 8.9mm flat edge screws from the top section of the top panel.
    • Using a Phillips00 screwdriver, remove two 8.9mm flat edge screws from the top section of the top panel.

  7. Using a Phillips00 screwdriver, remove two 10.3mm screws from the middle section of the top panel.
    • Using a Phillips00 screwdriver, remove two 10.3mm screws from the middle section of the top panel.

  8. Carefully pull the cover from the top panel and set it aside.
    • Carefully pull the cover from the top panel and set it aside.

  9. Using a Philips 00 screwdriver, remove the six 9.87mm screws securing the gear housing.
    • Using a Philips 00 screwdriver, remove the six 9.87mm screws securing the gear housing.

  10. Carefully pull apart the gear housing's panels.
    • Carefully pull apart the gear housing's panels.

    • The gears are lubricated by petroleum jelly.

  11. Gently pry the first gear out of the gear housing with a spudger.
    • Gently pry the first gear out of the gear housing with a spudger.

    • To ease reassembly, note the orientation of the gear as you pry it free.

  12. Gently pry the second gear out of the gear housing with a spudger.
    • Gently pry the second gear out of the gear housing with a spudger.

    • To ease reassembly, note the orientation of the gear before you pry it free.

  13. Gently pry the third gear out of the housing with a spudger.
    • Gently pry the third gear out of the housing with a spudger.

    • To ease reassembly, note the orientation of the gear as you pry it free.

まとめ

To reassemble your device, follow these instructions in reverse order.

Brian Eliason

メンバー登録日: 2014年10月27日

271 ポイント

2のガイドは作成済み

チーム

Eastern Washington University, Team 1-5, Carnegie Fall 2014 Eastern Washington University, Team 1-5, Carnegie Fall 2014人のメンバー

EWU-CARNEGIE-F14S1G5

7 メンバー

6のガイドは作成済み

統計データを表示:

過去 24時間: 0

過去 7 日: 5

過去 30 日: 20

今までの合計 1,560