はじめに
このガイドに従って、Xperia Z3のLCD ＆デジタイザの交換が可能です。
必要な工具と部品
-
-
バックカバーを加熱して、下の接着剤を緩めます。
-
iOpenerを使用する場合は、こちらの 使用ガイド を参照してください。
-
吸引ハンドルでバックカバーを持ち上げ、隙間にピックを入れてください。
-
ピックを慎重に端の周りに動かして、各側面にある接着剤を緩めます。
-
-
-
カバーの端に接着剤が付いていない場合は、デバイスを傾けるとバッテリーのタブを取り出すことができます。
-
ピンセットを使用して、2本の黒い接着ストリップを引き出しますが、まだここでは引っ張らないでください。
Careful during this bit. My old Z3 back cover couldn’t take it and split into lots of pieces (probably weakened over the years!). Just order a replacement for £3 off ebay before doing it ;-)
Merci pour ce tuto. Excellente procédure. Travaux réalisés en 20 minutes sans aucun problème. Attention: au remontage, il n'y a plus d'adhésif sur la batterie, la coque arrière peut éventuellement tomber. Je ne l'ai pas fait mais il faut peut-être mettre un petit double face sur la batterie.
-
-
-
-
ディスプレイを取り外すときにイヤースピーカーがディスプレイ側にくっついてきた場合は、ここで取り外して下さい。
-
iOpenerを使用して接着剤を柔らかくして、開口ピックをイヤホンとディスプレイの間でスライドさせ、イヤホンスピーカーを丁寧に外します。
The picture is misleading. If you try to remove the speaker with tweezers just how the picture depicts it, you will most likely rip it in two peaces like I did. Warming it up is absolutely necessary, but then just use a pick to loosen the adhesive underneath the speaker and remove it afterwards. For reassembly you will then need some new adhesive sticker for the speaker, but those are pretty cheap.
-
組立の際は、以下の手順を逆の順序で実行してください。
組立の際は、以下の手順を逆の順序で実行してください。
37 の人々がこのガイドを完成させました。
以下の翻訳者の皆さんにお礼を申し上げます:
100%
これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 あなたも貢献してみませんか？
翻訳を始める ›
7 件のコメント
What website is best to obtain a genuine screen and back from?
The back cover won’t fall off Josua but I would definitely recommend new adhesive!
But only for the phone to be waterproof? Because mine is definitely not waterproof anymore.. So I think this wouldn’t make any difference.
Josua -
In our case the back cover just held semi tight to the phone assembly without new adhesive. It could happen that the back cover falls off, when you pull the phone out of your pocket or you drop it. New adhesive also protects your phone from dust which can cause overheating.
Should adhesive also be used on the new front display? or will the old adhesive be enough by reheating it and letting it cool with the new display on the phone?
My Z3’s screen was “glitching,” as in the phone’s screen showed static noise from time to time. It was hard for me to do anything on the device, and the problem would be fixed for a really short amount of time by knocking on the phone (I know, that’s a very bad solution). Do you suppose that the cause of this weird “glitch” is an inconsistency of the LCD’s connector? Or can it be some other internal issue? How should I properly handle this problem?
How hot (how many C) should the iOpener be? I think it would be safer / more accurate to heat the iOpener in an oven with accurate temperature control.
Magnus Myklebost - 返信
Careful here. The back cover cracked in two places. Once when I exerted pressure with the suction handle, and in the corner when moving the pick around the edges- even though I was very gentle. The battery was adhered firmly to the back cover.
Joseph Doyle - 返信
I cracked the back cover instantly. Make sure to buy a spare one before opening!
raffaelecaroppo - 返信