メインコンテンツにスキップ

はじめに

This guide will replace the external speaker in the Sony Xperia Z1 Compact.

  1. Heat along the edges of the back cover  using a heat gun to soften the glue.
    • Heat along the edges of the back cover using a heat gun to soften the glue.

  2. Attach the small suction cup to the back cover near the bottom of the phone.
    • Attach the small suction cup to the back cover near the bottom of the phone.

    • Pull up on the suction cup and insert the plastic opening tool in between the back cover and the rest of the phone.

  3. Move the spudger around the edge of the back cover to separate it from the black adhesive. Separating the back cover from the rest of the phone ruins the adhesive which makes it no longer waterproof.
    • Move the spudger around the edge of the back cover to separate it from the black adhesive.

    • Separating the back cover from the rest of the phone ruins the adhesive which makes it no longer waterproof.

  4. Carefully disconnect the battery from the logic board by using the plastic spudger as a lever. Carefully disconnect the battery from the logic board by using the plastic spudger as a lever.
    • Carefully disconnect the battery from the logic board by using the plastic spudger as a lever.

  5. Remove the single 1 x 3.0 mm screw holding the battery in using the JIS #00 screwdriver. Remove the single 1 x 3.0 mm screw holding the battery in using the JIS #00 screwdriver.
    • Remove the single 1 x 3.0 mm screw holding the battery in using the JIS #00 screwdriver.

  6. Pry the battery up from the ends using the plastic spudger until the battery pops out of the enclosure.
    • Pry the battery up from the ends using the plastic spudger until the battery pops out of the enclosure.

  7. Remove the battery from the device
    • Remove the battery from the device

  8. Unscrew the four screws on the corners of the back frame using the JIS #00 screwdriver. Unscrew the four screws on the corners of the back frame using the JIS #00 screwdriver.
    • Unscrew the four screws on the corners of the back frame using the JIS #00 screwdriver.

  9. Wedge the plastic opening tool under the back frame. Move the plastic opening tool around the entire frame to separate it from the adhesive. Wedge the plastic opening tool under the back frame. Move the plastic opening tool around the entire frame to separate it from the adhesive. Wedge the plastic opening tool under the back frame. Move the plastic opening tool around the entire frame to separate it from the adhesive.
    • Wedge the plastic opening tool under the back frame. Move the plastic opening tool around the entire frame to separate it from the adhesive.

  10. Remove the back frame.
    • Remove the back frame.

  11. Wedge the spudger underneath the external speaker. Pull up on the external speaker using the spudger. Wedge the spudger underneath the external speaker. Pull up on the external speaker using the spudger.
    • Wedge the spudger underneath the external speaker. Pull up on the external speaker using the spudger.

  12. Remove the external speaker. Remove the external speaker.
    • Remove the external speaker.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Kevin Bergstrom

メンバー登録日: 2017年09月21日

346 ポイント

3のガイドは作成済み

チーム

Washington State, Team S4-G1, Phelps-Hillen Fall 2017 Washington State, Team S4-G1, Phelps-Hillen Fall 2017人のメンバー

WSU-PHELPS-HILLEN-F17S4G1

6 メンバー

9のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 14

今までの合計 710