Flip the computer so that the bottom is facing up.
  • Flip the computer so that the bottom is facing up.

  • Look to the long edge where the computer screen is hinged and find the "release slide". It is located at the top left corner of the square indent.

コメントを追加する

Use your finger to slide the release to the left.
  • Use your finger to slide the release to the left.

コメントを追加する

While holding the release slide with one hand, use your opposite hand to pull the battery from its slot by gently shaking the battery left and right to help slide  it out. While holding the release slide with one hand, use your opposite hand to pull the battery from its slot by gently shaking the battery left and right to help slide  it out.
  • While holding the release slide with one hand, use your opposite hand to pull the battery from its slot by gently shaking the battery left and right to help slide it out.

コメントを追加する

Take out the screw in the center of the computer.
  • Take out the screw in the center of the computer.

コメントを追加する

Flip the computer right side up.
  • Flip the computer right side up.

  • Open screen so that keyboard is visible.

コメントを追加する

Use a plastic opening tool to gently lift the keyboard at a corner. Make sure you get below the keyboard itself and not just the keys.
  • Use a plastic opening tool to gently lift the keyboard at a corner.

  • Make sure you get below the keyboard itself and not just the keys.

  • Slide the tool around the perimeter of the keyboard and it will start to lift.

コメントを追加する

Do not pull the keyboard away from the computer. There is a ribbon cord attaching the keyboard to the computer. Once the keyboard has been lifted at a few edges, lift the keyboard with both hands.
  • Do not pull the keyboard away from the computer. There is a ribbon cord attaching the keyboard to the computer.

  • Once the keyboard has been lifted at a few edges, lift the keyboard with both hands.

コメントを追加する

Locate the ribbon cord behind the keyboard. Locate a brown clamp attaching the keyboard to the computer. Use a plastic opening tool to lift the clamp and release the cable.
  • Locate the ribbon cord behind the keyboard.

  • Locate a brown clamp attaching the keyboard to the computer.

  • Use a plastic opening tool to lift the clamp and release the cable.

  • Now the keyboard can be pulled away entirely.

コメントを追加する

Take out the screw under the keyboard.
  • Take out the screw under the keyboard.

コメントを追加する

Flip computer over and remove the 6 screws.
  • Flip computer over and remove the 6 screws.

コメントを追加する

Flip computer over again and unclip the plastic cover.
  • Flip computer over again and unclip the plastic cover.

  • Do not be afraid to be rough, since the cover is hard to remove.

  • Be sure to remove the case slowly and unclip any ribbon cords that are attached.

コメントを追加する

Locate the hard drive disk. The hard drive disk will be covered by a shiny lid. Unscrew the lid with a #00 Phillips Head Screwdriver.
  • Locate the hard drive disk. The hard drive disk will be covered by a shiny lid.

  • Unscrew the lid with a #00 Phillips Head Screwdriver.

  • There are 3 screws holding it in.

  • Grab the lid by one corner and pull off the lid.

コメントを追加する

Find the brown clip attached to the hard disk drive on the side facing the optical disk drive.
  • Find the brown clip attached to the hard disk drive on the side facing the optical disk drive.

  • Carefully pull out the brown clip with your fingers.

コメントを追加する

Hold the hard disk drive on the side where the brown clip was attached and lift it upwards to pull it out.
  • Hold the hard disk drive on the side where the brown clip was attached and lift it upwards to pull it out.

コメントを追加する

Remove the 3 indicated screws. There are two small scews arounds the edge and one is on top of the optical drive. There are two small scews arounds the edge and one is on top of the optical drive.
  • Remove the 3 indicated screws.

  • There are two small scews arounds the edge and one is on top of the optical drive.

コメントを追加する

Remove the optical drive from resting positions. Gently remove cord.
  • Remove the optical drive from resting positions.

  • Gently remove cord.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Luke Thornley

メンバー登録日: 2012年04月03日

75 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 5-3, Forte Spring 2012 Cal Poly, Team 5-3, Forte Spring 2012人のメンバー

CPSU-FORTE-S12S5G3

5 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 3

今までの合計 1,262