メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

When completing this guide, remember the front buttons are flimsy so handle with care.

  1. Use a Phillips #00 screwdriver to unscrew the two 5 mm screws located on the bottom of the back of the device.
    • Use a Phillips #00 screwdriver to unscrew the two 5 mm screws located on the bottom of the back of the device.

  2. Use a plastic opening tool to loosen the bottom portion of device.
    • Use a plastic opening tool to loosen the bottom portion of device.

  3. Use a plastic opening tool to loosen the top panel of the device.
    • Use a plastic opening tool to loosen the top panel of the device.

  4. Use a Phillips #00 screwdriver to remove the two 3 mm screws located on the portion under the top panel of the device.
    • Use a Phillips #00 screwdriver to remove the two 3 mm screws located on the portion under the top panel of the device.

  5. Remove the back plate from the device. Remove the back plate from the device. Remove the back plate from the device.
    • Remove the back plate from the device.

  6. Peel back the layer of tape along with the processor, which is located just below the battery, using the tweezers and the spudger. Peel back the layer of tape along with the processor, which is located just below the battery, using the tweezers and the spudger.
    • Peel back the layer of tape along with the processor, which is located just below the battery, using the tweezers and the spudger.

  7. Slide a prying tool underneath the top portion of the battery and lift it from the case. Slide a prying tool underneath the top portion of the battery and lift it from the case.
    • Slide a prying tool underneath the top portion of the battery and lift it from the case.

  8. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  9. Remove the stickers from the battery terminals, which are on the underside of the battery.
    • Remove the stickers from the battery terminals, which are on the underside of the battery.

  10. Use a soldering iron to remove the wires from the red and the black terminals.
    • Use a soldering iron to remove the wires from the red and the black terminals.

  11. Use a nylon spudger or tweezers to remove the plastic USB cover.
    • Use a nylon spudger or tweezers to remove the plastic USB cover.

  12. Use a Phillips #00 screwdriver to unscrew two 2 mm screws located on the top corners of the device.
    • Use a Phillips #00 screwdriver to unscrew two 2 mm screws located on the top corners of the device.

  13. Use a nylon spudger or tweezers to remove the plastic protective plate at the top of device.
    • Use a nylon spudger or tweezers to remove the plastic protective plate at the top of device.

  14. Remove the plastic protective frame located over the motherboard with tweezers and a spudger. Remove the plastic protective frame located over the motherboard with tweezers and a spudger.
    • Remove the plastic protective frame located over the motherboard with tweezers and a spudger.

  15. Remove screen connection from motherboard using tweezers and spudger.
    • Remove screen connection from motherboard using tweezers and spudger.

  16. Use a Phillips #00 screwdriver to remove two 3 mm screws at the bottom sides and two 1 mm screws at top sides of the device.
    • Use a Phillips #00 screwdriver to remove two 3 mm screws at the bottom sides and two 1 mm screws at top sides of the device.

  17. Use a Phillips #00 screwdriver to unscrew two 2 mm screws, and remove the motherboard from the device with tweezers and a plastic opening tool. Use a Phillips #00 screwdriver to unscrew two 2 mm screws, and remove the motherboard from the device with tweezers and a plastic opening tool.
    • Use a Phillips #00 screwdriver to unscrew two 2 mm screws, and remove the motherboard from the device with tweezers and a plastic opening tool.

  18. Disconnect the metal shielding plate from the front panel with tweezers or a plastic opening tool. Disconnect the metal shielding plate from the front panel with tweezers or a plastic opening tool.
    • Disconnect the metal shielding plate from the front panel with tweezers or a plastic opening tool.

  19. Use a plastic opening tool to remove the screen from metal back plate. Use a plastic opening tool to remove the screen from metal back plate.
    • Use a plastic opening tool to remove the screen from metal back plate.

  20. Ensure that button connection is completely separated from the buttons.
    • Ensure that button connection is completely separated from the buttons.

  21. Remove buttons from front display panel by  pushing button display from the front of the device Remove buttons from front display panel by  pushing button display from the front of the device Remove buttons from front display panel by  pushing button display from the front of the device
    • Remove buttons from front display panel by pushing button display from the front of the device

終わりに

To reassemble your device, follow these instructions in reverse order.

Matthew Hintz

メンバー登録日: 2015年01月16日

327 ポイント

3のガイドは作成済み

チーム

USF Tampa, Team 17-6, Watkins Winter 2015 USF Tampa, Team 17-6, Watkins Winter 2015人のメンバー

USFT-WATKINS-W15S17G6

4 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 6

今までの合計 1,175