Sony Handycam DCR-DVD103 LCD Screen Replacement

はじめに

Occasionally the LCD screen or the Back light on the camera will be cracked or simply stop working. This page outlines how to disassemble the camera in order to install replacement parts for any broken pieces.

必要な工具と部品

手順1 Battery

Sony Handycam DCR-DVD103 LCD Screen Replacement, Battery: 手順 1、 1の画像 1

Images do not show the camera's battery.
On the back of the camera beneath the viewfinder, locate the battery pack.
Press the small button.
Slide the switch forward.

編集

手順2

Remove the battery from the camera.
To reinsert the battery, slide the battery into the camera.

編集

手順3 Outer Cover

Sony Handycam DCR-DVD103 LCD Screen Replacement, Outer Cover: 手順 3、 1の画像 1

Using a #00 Phillips screwdriver, remove the six 4.5 mm screws from the camera's bottom.

編集

手順4

Remove the three 4.5 mm screws beneath the battery.
Remove the 2.9 mm screw from the right corner.
Remove the two 4.5 mm screws from the battery's right wall.
Images do not show the battery.

編集

手順5

Remove the 4.5 mm screw under the output flap on the front of the camera below the lens.

編集

手順6

Remove the two 4.5 mm screws at the top of the camera.
Remove the 4.5 mm screw from the disk side of the camera (next to the lens).

編集

手順7

Extend the gray viewfinder, then gently remove the black plastic casing.
Caution: Plastic pieces are fragile.

編集

手順8

Remove the two 2.9 mm screws under the black plastic casing.

編集

手順9

Gently pull apart the outer silver case and screen.
Remove the copper wire strip to detach the case from the camera.

編集

手順10 LCD Screen

Sony Handycam DCR-DVD103 LCD Screen Replacement, LCD Screen: 手順 10、 1の画像 1

Remove the copper strip from the housing that connects the outer casing to the entire of the camera.
Use caution when removing the wire, too much force may cause it to tear.

編集

手順11

Sony Handycam DCR-DVD103 LCD Screen Replacement: 手順 11、 3の画像 3

Remove (4) 2.9mm screws from the L-shaped circuit board. They are marked with red circles in the slide.
Remove the (3) wire strips connected to the camera so you can pull off the L-shaped circuit board.
Remove the single wire strip that is connected to the bottom of the circuit board.

編集

手順12

Remove the (2) 4.5mm screws.
Remove the small black holder from above the base of the LCD screen.

編集

手順13

Remove (1) 2.9mm screw from the base of the LCD screen.

編集

手順14

Remove the silver and black, front and back casings from the base of the screen.
Remove one copper strip from the inside of the bottom case.

編集

手順15

Remove (2) 5.4mm screws that are securing the screen to the cover, from the base of the LCD.

編集

手順16

Sony Handycam DCR-DVD103 LCD Screen Replacement: 手順 16、 3の画像 3

Twist out the screen from the cover.
Be careful not to break the casing when trying to get the screen out, as it does require some maneuvering.

編集

手順17

Remove (2) 3.8mm screws from the end of the LCD.

編集

手順18

Remove (2) 3.8mm screws from the bottom of the LCD.

編集

手順19

Pull off the silver cover on the screen, which will reveal the circuit board from behind the screen itself.
Pull off the black tape stuck to both sides of the circuit board.

編集