危険
潜在的な危険
この手順に正しく従わない場合は損傷が生じる可能性があります。ご注意のうえ使用し、すべての警告に従ってください。
危険

はじめに

This installation guide allows you to remove the power supply circuit board and power cable.

パーツ

パーツは必要ありません。

Remove the five #1 Phillips screws (black, 3/16") attaching the cover to the DVD player. One 3/16" screw on the right side of the DVD player.
  • Remove the five #1 Phillips screws (black, 3/16") attaching the cover to the DVD player.

    • One 3/16" screw on the right side of the DVD player.

    • One 3/16" screw on the left side of the DVD player (directly opposite of other screw).

    • Three 3/16" screws on the back of the DVD player.

コメントを追加する

Slide the cover away from the front of the DVD player until it is off. Slide the cover away from the front of the DVD player until it is off.
  • Slide the cover away from the front of the DVD player until it is off.

コメントを追加する

Remove the blue tape from the processing board by gently pulling upward.
  • Remove the blue tape from the processing board by gently pulling upward.

コメントを追加する

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Use the tweezers to remove the four sets of wires connected to the processing board.  Start with the cord located in front of the row of three cords. The wires may be difficult to remove.  Wiggling them while lifting them up may help remove them.
  • Use the tweezers to remove the four sets of wires connected to the processing board. Start with the cord located in front of the row of three cords.

  • The wires may be difficult to remove. Wiggling them while lifting them up may help remove them.

コメントを追加する

Handle the processing board with care.  It is fragile.
  • Handle the processing board with care. It is fragile.

  • Unscrew the two #1 Phillips screws (silver, 3/16") located on the two edge corners of the processing board.

コメントを追加する

Orient the DVD player so that you are facing the video and audio jacks.
  • Orient the DVD player so that you are facing the video and audio jacks.

  • Unscrew the two #1 Phillips screws (silver, 3/16") located on the outside of the DVD player

  • The processing board is now free to be removed and replaced.

コメントを追加する

Beware of the capacitors.
  • Beware of the capacitors.

  • The capacitors may shock you if touched.

  • Unhook the power supply connector from the power supply board by pressing down on the small latch.

コメントを追加する

Orient the DVD player so the back of the DVD player is opposite of you.
  • Orient the DVD player so the back of the DVD player is opposite of you.

  • Unscrew the two #1 Phillips screws (silver, 3/16") that attach the power supply circuit board to the bottom of the DVD player.

I thought it's the power supply board that needs to be replaced. Why is the the processing board being removed and replaced in this instruction?

djingsaquino - 返信

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Brian Hua

メンバー登録日: 2013年01月11日

58 ポイント

3のガイドは作成済み

チーム

Cal Poly, Team 5-17, Forte Winter 2013 Cal Poly, Team 5-17, Forte Winter 2013人のメンバー

CPSU-FORTE-W13S5G17

5 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 16

過去 30 日: 88

今までの合計 5,826