はじめに

Replace motherboard.

パーツ

パーツは必要ありません。

  1. Remove Memory Stick Pro from the card reader slot on the bottom of the camera.
    • Remove Memory Stick Pro from the card reader slot on the bottom of the camera.

    • Remove both batteries.

    コメントを追加する

  2. Remove the single visible screw from both sides of the camera.
    • Remove the single visible screw from both sides of the camera.

    • Remove the two screws that are adjacent to the warning label, which is on the underside of the camera.

    • Do NOT remove all four screws from the bottom.

    コメントを追加する

    • Gently remove the back cover from the camera.

    • The first time the case is removed, it will be stiff. Be patient and gently rock the cover back and forth until it slides free.

    コメントを追加する

    • Remove the two screws holding the circuit board down.

    コメントを追加する

    • Detach the orange cable from the board.

    • Use a thin object, like a paperclip, to gently pry the cable off the connector.

    コメントを追加する

    • The LCD screen sits in two slots; one on the bottom, and one on the left edge.

    • Slide LCD screen from the two slots.

    • Do not attempt to completely remove the screen, as it is still attached to the camera.

    コメントを追加する

    • To remove the LCD screen, detach the orange cable from the board.

    • If needed, replace the LCD screen.

    コメントを追加する

    • Remove the two screws holding down the steel back plate.

    • Remove steel back plate.

    コメントを追加する

    • Now remove the plastic plate that covers the motherboard.

    Below and to the left of the viewfinder there is a vertical slot in the motherboard with a soldered connection to the flash capacitor on each side. Using a small screwdriver with an INSULATED handle, short these together for several seconds to discharge the potentially dangerous charge.

    Philip Le Riche - 返信

    • Warning: Electric Shock From this point on, hold the camera by the chrome edges ONLY. Capacitors store electric charge even if the batteries are removed.

    • Remove the blue cable.

    コメントを追加する

    • Disconnect the flash cable (black and white wires) before completely removing the front case.

    • Gently start to remove the case.

    • Once the cable is free, set aside the front case.

    If the front doesn't seem to want to come away, maybe the flash cable is caught around its socket.

    Philip Le Riche - 返信

    • The speaker should now be clearly seen on the underside of the camera.

    • Gently unplug the speaker from the motherboard.

    • Replace the speaker.

    コメントを追加する

    • Remove the orange cable connecting the battery terminal to the motherboard.

    コメントを追加する

    • The battery terminal is now free from the board and can be slid out.

    コメントを追加する

    • Detach two cables that go from the motherboard to the lens.

    • Remove lens.

    コメントを追加する

    • After the lens is detached, you can replace the motherboard.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Thomas

メンバー登録日: 2010年04月14日

109 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 15-50, Garner Spring 2010 Cal Poly, Team 15-50, Garner Spring 2010人のメンバー

CPSU-GARNER-S10S15G50

5 メンバー

6のガイドは作成済み

コメント1件

Thank yo very much, Muy agradecido por la información. Good information fireman4792000@yahoo.com

Jorge - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 3

今までの合計 5,235