修理を始めるには コミュニティ ストア

Shark Ultimate Professional Circuit Board Replacement

はじめに

Before beginning this guide, ensure that the device is both unplugged and cool; failure to do so may result in electrocution or burns.

必要な工具と部品

  1. Shark Ultimate Professional Circuit Board Replacement, Circuit Board: 手順 1、 3の画像 1 Shark Ultimate Professional Circuit Board Replacement, Circuit Board: 手順 1、 3の画像 2 Shark Ultimate Professional Circuit Board Replacement, Circuit Board: 手順 1、 3の画像 3

    • Use the Philips head #0 screwdriver to remove the two 11.49mm screws at the back of the iron.

    • Remove the back cover piece.

    • Make sure the iron is unplugged and cooled off.

    翻訳

  2. Shark Ultimate Professional Circuit Board Replacement: 手順 2、 2の画像 1 Shark Ultimate Professional Circuit Board Replacement: 手順 2、 2の画像 2

    • Use the Philips head #0 screwdriver to remove the two 11.77mm screws holding the white clamp to the iron.

    • Use the Philips head #0 screwdriver to remove the two 6.58mm screws holding the black wires to the body of the iron.

    • Removing the left black wire will also free the red wire, attached by the same screw.

    翻訳

  3. Shark Ultimate Professional Circuit Board Replacement: 手順 3、 1の画像 1

    • Pull the split end of the power cord upward through the ball joint.

    • Set aside the power cord.

    翻訳

  5. Shark Ultimate Professional Circuit Board Replacement: 手順 4、 3の画像 1 Shark Ultimate Professional Circuit Board Replacement: 手順 4、 3の画像 2 Shark Ultimate Professional Circuit Board Replacement: 手順 4、 3の画像 3

    • Use the Philips head #0 screwdriver to remove the remaining 6.58mm screws that hold the wires on the bottom (brown and blue).

    • Remove from left to right

    • Unclip the black adapter piece on the bottom right.

    • Wires order (from left to right): Brown, Blue, Red, Black

    翻訳

  6. Shark Ultimate Professional Circuit Board Replacement: 手順 5、 2の画像 1 Shark Ultimate Professional Circuit Board Replacement: 手順 5、 2の画像 2

    • Use the Philips head #0 screwdriver to remove the two 9.75mm screws (left and right) affixed to the circuit board.

    翻訳

  7. Shark Ultimate Professional Circuit Board Replacement: 手順 6、 2の画像 1 Shark Ultimate Professional Circuit Board Replacement: 手順 6、 2の画像 2

    • Use the Philips head #0 screwdriver to remove the two 9.82mm screws (left and right) from the white border on top of the circuit board.

    • Gently pull the circuit board from affixed position.

    • The circuit board will not be completely separated at this point.

    翻訳

  8. Shark Ultimate Professional Circuit Board Replacement: 手順 7、 3の画像 1 Shark Ultimate Professional Circuit Board Replacement: 手順 7、 3の画像 2 Shark Ultimate Professional Circuit Board Replacement: 手順 7、 3の画像 3

    • Remove the mode display piece and set aside.

    • Lift the handle and wiggle the plastic trim and the orange-chrome bezel out from under the handle.

    翻訳

  9. Shark Ultimate Professional Circuit Board Replacement: 手順 8、 1の画像 1

    • Remove the connecting wire from the connected adapter in the handle by pulling lightly.

    • Set aside the circuit board.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

5 の人々がこのガイドを完成させました。

作成者

5人の作成者と共同で作成されました。

Drew Carff

メンバー登録日: 10/23/17

868 ポイント

5のガイドは作成済み

バッジ: 14

+11 個以上のバッジ

チーム

USF Tampa, Team S1-G4, Leahy Fall 2017 USF Tampa, Team S1-G4, Leahy Fall 2017人のメンバー

USFT-LEAHY-F17S1G4

3 メンバー

10のガイドは作成済み

4 件のコメント

My shark 1505C does not have philips screws on the back. They are security torx and I cannot find a tool to open it.

Where can I buy a main board for this iron ?

Thanks

NevG.

nevstarg - 返信

where do I buy it's circuit board?

egovieira - 返信

Where can u buy the circuit board professional 1800 version?

Astinder Singhera - 返信

How much does the circuit board cost? and where can i purchase it?

D.A. Willis - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 4

過去 30 日: 27

今までの合計 3,064