修理を始めるには コミュニティ ストア

Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement

はじめに

When the roller brush is not spinning because of blockage or damage, you might want to consider replacing it.

必要な工具と部品

  1. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement, Roller Brush: 手順 1、 2の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement, Roller Brush: 手順 1、 2の画像 2

    • Push the red Lift Away button down and lift up on the vacuum handle to detach the base.

    • The handle was removed for convenience but is not required.

    編集

  2. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 2、 1の画像 1

    • Turn over the vacuum to reveal the roller brush.

    編集

  3. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 3、 2の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 3、 2の画像 2

    • Pry the small wheels at the bottom of the base using the plastic opening tool.

    編集

  4. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 4、 2の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 4、 2の画像 2

    • Using a coin, turn the big white knobs located above the roller brush counter-clockwise.

    編集

  6. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 5、 3の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 5、 3の画像 2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 5、 3の画像 3

    • Lift up the suction hose to reveal a screw.

    • Remove the 12.7 mm Phillips #02 screw.

    編集

  7. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 6、 2の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 6、 2の画像 2

    • Remove eight 12.7mm screws located under the vacuum using a Phillips #02 screwdriver.

    • Remove two 12.7 mm screws located next to the wheels with a Phillips #02 screwdriver.

    • The two screws located next to the wheels are smaller in diameter.

    編集

  8. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 7、 3の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 7、 3の画像 2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 7、 3の画像 3

    • Turn the vacuum upright and pull the white upper section of the brush roller circuit housing.

    • Be careful when lifting the housing as there is a connector attached.

    編集

  9. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 8、 2の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 8、 2の画像 2

    • Remove the connector attached to the circuit boards using a plastic opening tool.

    編集

  10. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 9、 3の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 9、 3の画像 2 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 9、 3の画像 3

    • Remove the two 12.7 mm screws located at the top of the clear plastic brush roller housing using a Phillips #02 screwdriver.

    • Lift the clear plastic brush roller housing.

    編集

  11. Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 10、 2の画像 1 Shark Rotator Slim-Light Lift-Away Upright Roller Brush Replacement: 手順 10、 2の画像 2

    • Wiggle the brush roller upwards from the left and right side slots.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

3人の作成者と共同で作成されました。

Daniel Ceja

メンバー登録日: 01/24/19

277 ポイント

2のガイドは作成済み

バッジ: 6

+3 個以上のバッジ

チーム

Cal Poly, Team S19-G3, White Winter 2019 Cal Poly, Team S19-G3, White Winter 2019人のメンバー

CPSU-WHITE-W19S19G3

5 メンバー

12のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 4

過去 30 日: 10

今までの合計 954