修理を始めるには コミュニティ ストア

この修理ガイドは変更されています。最新の未承認バージョンに切り替えます。

Shark Rotator Powered Lift-Away Speed Belt Replacement

はじめに

The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum's belt is designed to last approximately 7 years. Replacement of the belt is needed to keep the vacuum at optimal working condition. This replacement guide demonstrates how to replace the belt in the vacuum.

必要な工具と部品

  1. Shark Rotator Powered Lift-Away Speed Belt Replacement, Belt: 手順 1、 3の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement, Belt: 手順 1、 3の画像 2 Shark Rotator Powered Lift-Away Speed Belt Replacement, Belt: 手順 1、 3の画像 3

    • Turn the vacuum on its side.

    • Using a quarter, twist the three green locks to the unlock position.

    • Pull the bottom roller brush cover to open the vacuum.

    翻訳

  2. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 2、 1の画像 1

    • Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    翻訳

  3. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 3、 2の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 3、 2の画像 2

    • Remove the three 14.3 mm screws with a T20 screwdriver.

    翻訳

  4. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 4、 1の画像 1

    • Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    翻訳

  5. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 5、 1の画像 1

    • Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    翻訳

  6. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 6、 1の画像 1

    • Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    翻訳

  8. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 7、 1の画像 1

    • Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    翻訳

  9. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 8、 3の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 8、 3の画像 2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 8、 3の画像 3

    • Turn the vacuum around.

    • Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    翻訳

  10. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 9、 2の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 9、 2の画像 2

    • Remove both of the headlight covers with the spudger.

    翻訳

  11. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 10、 3の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 10、 3の画像 2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 10、 3の画像 3

    • Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    翻訳

  12. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 11、 1の画像 1

    • Remove the two 13.4 mm screws with a T20 bit screwdriver.

    翻訳

  13. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 12、 1の画像 1

    • Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    翻訳

  14. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 13、 3の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 13、 3の画像 2 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 13、 3の画像 3

    • Remove the visible side of the belt from the gear with a spudger.

    翻訳

  15. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 14、 1の画像 1

    • Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    翻訳

  16. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 15、 2の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 15、 2の画像 2

    • Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    翻訳

  17. Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 16、 2の画像 1 Shark Rotator Powered Lift-Away Speed Belt Replacement: 手順 16、 2の画像 2

    • Remove the belt from the gear.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

3人の作成者と共同で作成されました。

Dakota Rodriguez-Ransom

メンバー登録日: 10/08/18

605 ポイント

2のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

Cal Poly, Team S4-G6, White Fall 2018 Cal Poly, Team S4-G6, White Fall 2018人のメンバー

CPSU-WHITE-F18S4G6

4 メンバー

12のガイドは作成済み

2 件のコメント

Where can we buy belts in UK?

Greg Norman - 返信

where cn i get a belt for this vaccum

Annie Pappineau - 返信

コメントを追加

統計データ:

過去 24時間: 34

過去 7 日: 233

過去 30 日: 1,117

今までの合計 37,803