メニュー

Your Settings

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Shark Rotator Powered Lift-Away Speed Belt Replacement

作成者： Dakota Rodriguez-Ransom (そして 3 人のその他投稿者)
  • コメント: 0
  • お気に入り: 0

難易度

普通

手順

16

所要時間

1 - 2 時間

セクション

1

フラグ

0

はじめに

The Shark Rotator Powered Lift-Away has one rotatory belt. The belt is responsible for the mechanical rotations of the brushroll. Without it, the vacuum will not function. The vacuum's belt is designed to last approximately 7 years. Replacement of the belt is needed to keep the vacuum at optimal working condition. This replacement guide demonstrates how to replace the belt in the vacuum.

ツール

これらのツールを購入する

パーツ

パーツは必要ありません。

  1. Turn the vacuum on its side. Using a quarter, twist the three green locks to the unlock position. Pull the bottom roller brush cover to open the vacuum.

    • Turn the vacuum on its side.

    • Using a quarter, twist the three green locks to the unlock position.

    • Pull the bottom roller brush cover to open the vacuum.

    翻訳

  2. Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    • Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    翻訳

  3. Remove the three 14.3 mm screws with a T20 screwdriver. Remove the three 14.3 mm screws with a T20 screwdriver.

    • Remove the three 14.3 mm screws with a T20 screwdriver.

    翻訳

  4. Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    • Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    翻訳

  5. Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    • Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    翻訳

  6. Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    • Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    翻訳

  7. Free shipping on all orders over $100.00 or containing a Pro Tech Toolkit!

    当社のショップを閲覧する

  8. Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    • Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    翻訳

  9. Turn the vacuum around. Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights. Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    • Turn the vacuum around.

    • Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    翻訳

  10. Remove both of the headlight covers with the spudger. Remove both of the headlight covers with the spudger.

    • Remove both of the headlight covers with the spudger.

    翻訳

  11. Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel. Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel. Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    • Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    翻訳

  12. Remove the two 13.4 mm screws with a T20 bit screwdriver.

    • Remove the two 13.4 mm screws with a T20 bit screwdriver.

    翻訳

  13. Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    • Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    翻訳

  14. Remove the visible side of the belt from the gear with a spudger. Remove the visible side of the belt from the gear with a spudger. Remove the visible side of the belt from the gear with a spudger.

    • Remove the visible side of the belt from the gear with a spudger.

    翻訳

  15. Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    • Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    翻訳

  16. Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward. Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    • Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    翻訳

  17. Remove the belt from the gear. Remove the belt from the gear.

    • Remove the belt from the gear.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

作成者

3他の投稿者と一緒に

Dakota Rodriguez-Ransom

メンバー登録日: 2018年10月08日

587 ポイント

2のガイドは作成済み

バッジ: 5

+2 個以上のバッジ

チーム

Cal Poly, Team S4-G6, White Fall 2018 Cal Poly, Team S4-G6, White Fall 2018人のメンバー

CPSU-WHITE-F18S4G6

4 メンバー

5のガイドは作成済み

0コメント

コメントを追加
統計データを表示:

過去 24時間: 0

過去 7 日: 13

過去 30 日: 41

今までの合計 121