修理を始めるには コミュニティ ストア

Shark Rotator Lift-Away Speed Brushroll Motor Replacement

はじめに

The brushroll motor is what powers the brushroll and makes it spin. If the brushroll is spinning, the motor may need to be replaced.

必要な工具と部品

  1. Shark Rotator Lift-Away Speed Brushroll Motor Replacement, Brushroll: 手順 1、 1の画像 1

    • Make sure the vacuum is turned off and unplugged before proceeding.

    • Locate the release button at the top of the vacuum pod next to the handle.

    • Use the handle to lift the pod up off of the vacuum nozzle while pressing the release button.

    • Removing the pod is optional, but it may be easier to locate blockages or access the motor and belt if you do so.

    編集

  2. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 2、 2の画像 1 Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 2、 2の画像 2

    • Press the Brushroll Access buttons on the top of the nozzle to reveal the brushroll compartment.

    編集

  3. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 3、 2の画像 1 Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 3、 2の画像 2

    • Lift the brushroll out by using the pull-tab on the left side.

    • You can test the brushroll once it has been inserted by plugging the vacuum in and running the vacuum in carpet mode. The brushroll indicator light should be a solid green color.

    編集

  5. Shark Rotator Lift-Away Speed Brushroll Motor Replacement, Brushroll Motor: 手順 4、 1の画像 1

    • Remove the five 5mm Torx #9 screws on the front side.

    編集

  6. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 5、 1の画像 1

    • Remove the six 7.5mm Torx #20 screws on the bottom face of the nozzle.

    • A screwdriver extension may be necessary to reach the screw closest to the center of the nozzle.

    編集

  7. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 6、 1の画像 1

    • Remove the top panel by lifting the top piece off of the bottom.

    • There will be loud clicking noises.

    編集

  8. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 7、 1の画像 1

    • If you are trying to remove the belt, you may skip to the next step.

    • Remove the 7.5mm Torx #20 screw in front of the motor.

    • The motor is the gray block on the right side of the floor nozzle (when the nozzle faces towards you).

    編集

  9. Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 8、 2の画像 1 Shark Rotator Lift-Away Speed Brushroll Motor Replacement: 手順 8、 2の画像 2

    • If you are trying to remove the belt, you may skip to the next step.

    • Remove the panel to reveal the motor screw.

    • Remove the 7.5mm Torx #20 motor screw.

    • Remove the motor.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

2人の作成者と共同で作成されました。

Weston Mongomery

メンバー登録日: 10/02/17

201 ポイント

2のガイドは作成済み

バッジ: 4

+1 以上のバッジ

チーム

Cal Poly, Team S15-G7, Livingston Fall 2017 Cal Poly, Team S15-G7, Livingston Fall 2017人のメンバー

CPSU-LIVINGSTON-F17S15G7

4 メンバー

10のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 2

過去 7 日: 7

過去 30 日: 25

今までの合計 3,733