メインコンテンツにスキップ

このバージョンは誤った内容を含んでいる可能性があります。最新の承認済みスナップショットに切り替えてください。

必要な工具と部品

  1. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 1、 2の画像 1 : 手順 1、 2の画像 2
    • Open the garage door by sliding both of the release buttons away from you.

    • Lift off the garage door.

  2. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 2、 2の画像 1 : 手順 2、 2の画像 2
    • Remove the plastic screw covering using a metal spudger by pushing the sharp side into the crevice and prying the cover out.

  3. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 3、 2の画像 1 : 手順 3、 2の画像 2
    • Turn the T10 Security Torx screwdriver counterclockwise to remove the 15mm screw.

  4. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 4、 1の画像 1
    • Use the iFixit Opening Tool to pry the side of the vacuum open.

  5. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 5、 1の画像 1
    • Remove the side component with your hands.

  6. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 6、 1の画像 1
    • Remove the four 15 mm T10 screws on the underside of the vacuum.

  7. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 7、 2の画像 1 : 手順 7、 2の画像 2
    • Using the plastic spudger, pry the back seam of the top component to pop it off the vacuum.

  8. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 8、 2の画像 1 : 手順 8、 2の画像 2
    • Orient the vacuum so you are looking down at the open garage of the vacuum.

    • Using your right hand, rotate the top of the silver motor towards the brush roll of the vacuum so the motor fits through the opening.

  9. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 9、 1の画像 1
    • With both thumbs, push the gear on the right side of the motor into the vacuum. The motor should pop out.

    • Slowly pull the motor out of the vacuum base and reveal the electrical cords.

  10. この手順は未翻訳です。 翻訳を手伝う。

    : 手順 10、 1の画像 1
    • To fully remove the motor, cut the wires.

    • For reassembly, use the soldering guide in the Introduction.

ゴール

6 の人々がこのガイドを完成させました。

作成者

4人の作成者と共同で作成されました。

Samantha Mickelson

メンバー登録日: 10/08/18

496 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team S17-G5, White Fall 2018 Cal Poly, Team S17-G5, White Fall 2018人のメンバー

CPSU-WHITE-F18S17G5

4 メンバー

14のガイドは作成済み

7 件のコメント

Can this motor we test it before taking it out

craigfranz - 返信

Can this motor be tested before taking it out?

craigfranz - 返信

How do I know if the motor is burned out

Danny Manuele -

Will you be able to take out the brush roll in front of the motor?

CAM BAP - 返信

Great fix. I wonder if you know how to find a replacement motor? My Dyson motor died and I’m not sure where to start looking for a replacement part - Dyson don’t sell it.

TyN - 返信

コメントを追加

統計データ:

過去 24時間: 2

過去 7 日: 45

過去 30 日: 216

今までの合計 21,545