メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Sega Game Gear Screen Replacement

おすすめ

作成者： Lauren Thurston (そして 5 人のその他投稿者)
  • コメント: 4
  • お気に入り: 17
  • 完了: 8

おすすめのガイド

難易度

普通

手順

12

所要時間

30 - 45 分

セクション

3

フラグ

1

Featured Guide

おすすめのガイド

このガイドはiFixitスタッフによって太鼓判が押されています。

はじめに

A guide to installing a replacement screen on a Sega Game Gear.

ツール

これらのツールを購入する

パーツ

パーツは必要ありません。

  1. Place your device upside down and locate the two battery compartments.

    • Place your device upside down and locate the two battery compartments.

    翻訳

  2. Press on the tabs at the bottom of the battery covers then lift up to remove.

    • Press on the tabs at the bottom of the battery covers then lift up to remove.

    • Remove batteries if they are present.

    翻訳

  3. Remove the following screws:

    • Remove the following screws:

    • Seven Phillips scres

    • One 4.5 mm Gamebit screw

    翻訳

  4. Use tweezers to take all other screws out.

    • Use tweezers to take all other screws out.

    翻訳

  5. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する

  6. Gently open the case by unfolding it over the top of the Sega Game Gear. Do not pull the back of the case away, as cables are connected between both sides.

    • Gently open the case by unfolding it over the top of the Sega Game Gear.

    • Do not pull the back of the case away, as cables are connected between both sides.

    翻訳

  7. Carefully unplug the 2 white-tipped connectors on the top cover. Carefully unplug the 2 white-tipped connectors on the top cover. Carefully unplug the 2 white-tipped connectors on the top cover.

    • Carefully unplug the 2 white-tipped connectors on the top cover.

    翻訳

  8. Unscrew all the marked screws.

    • Unscrew all the marked screws.

    翻訳

  9. Slide the logic board out from under the circular black fastener at the top-left corner of the case.

    • Slide the logic board out from under the circular black fastener at the top-left corner of the case.

    翻訳

  10. Place the board onto a flat surface.

    • Place the board onto a flat surface.

    • Small plastic buttons may fall off during this process, save them in a container or a place where they could be found later on.

    翻訳

  11. Unscrew the marked screws.

    • Unscrew the marked screws.

    • Flip the board, having its back facing up.

    • Hold onto the screen in the back, as it will flip open if not held onto.

    翻訳

  12. Make sure the screen is towards the bottom, as indicated in the second picture. Make sure the screen is towards the bottom, as indicated in the second picture.

    • Make sure the screen is towards the bottom, as indicated in the second picture.

    翻訳

  13. Gently open the screen up. The screen will not come out all the way since it is glued onto the top side.

    • Gently open the screen up.

    • The screen will not come out all the way since it is glued onto the top side.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

8 の人々がこのガイドを完成させました。

作成者

5他の投稿者と一緒に

Lauren Thurston

メンバー登録日: 2010年04月15日

296 ポイント

3のガイドは作成済み

バッジ: 13

+10 個以上のバッジ

チーム

Cal Poly, Team 28-33, Regan Spring 2010 Cal Poly, Team 28-33, Regan Spring 2010人のメンバー

CPSU-REGAN-S10S28G33

5 メンバー

6のガイドは作成済み

4コメント

コメントを追加

any one know where to get a new display that wont bleed me dry?

isaiah bellamy (masta ike) - 返信

Due to the nature a Game Gear screen attaches, a ribbon directly soldered to the mainboard, replacing it requires a soldering iron and some fairly advanced technique.

This guide, titled “Sega Game Gear Screen Replacement”, only takes us to the point you remove the ribbon. There is much work left.

Anthony Bessel - 返信

so, uh, is there a more comprehensive version somewhere?

rollin -

Does the screen get fixed at the end?

Caedmon O’Brien - 返信

コメントを追加する

1024

統計データを表示:

過去 24時間: 6

過去 7 日: 57

過去 30 日: 299

今までの合計 43,070