メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

Use this guide to remove the power supply unit.

パーツ

パーツは指定されていません。

  1. Place the monitor face down.
    • Place the monitor face down.

    • Remove the four 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the stand by pulling it out.

  2. Remove two 11.5mm screws with a  #2 Phillips screwdriver.
    • Remove two 11.5mm screws with a #2 Phillips screwdriver.

    • Remove the plastic bar.

  3. Using a  #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.
    • Using a #2 Phillips screwdriver, remove the six 7mm screws at the circled locations.

  4. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  5. Pry the monitor using the plastic opening tool to release the clips holding the cover on. There are four clips on each side, four on the top, and one on the bottom. You may hear a loud snapping noise when releasing the clips.  Do not be alarmed, it is natural.
    • Pry the monitor using the plastic opening tool to release the clips holding the cover on.

    • There are four clips on each side, four on the top, and one on the bottom.

    • You may hear a loud snapping noise when releasing the clips. Do not be alarmed, it is natural.

    • Once all the clips have been released, remove the cover by pulling it up.

  6. Using the  #2 Phillips screwdriver, remove the one 6mm screw. Unplug the indicated cable by pulling on the base.
    • Using the #2 Phillips screwdriver, remove the one 6mm screw.

    • Unplug the indicated cable by pulling on the base.

    • Slide the cover toward the top of the monitor.

    • Remove the cover.

  7. Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.
    • Using a #2 Phillips screwdriver, remove the two 4.72 mm Phillips screws that hold the power adapter in place.

  8. Unplug the seven connections from the power supply unit by gently pulling on them. Unplug the seven connections from the power supply unit by gently pulling on them. Unplug the seven connections from the power supply unit by gently pulling on them.
    • Unplug the seven connections from the power supply unit by gently pulling on them.

  9. Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.
    • Using a #2 Phillips screwdriver, remove the screws and the wire that is attached to the ground.

    • Four 6 mm Phillips screws

    • One 8 mm Phillips screw

  10. Lift the power supply unit straight up to remove it from the back panel. Lift the power supply unit straight up to remove it from the back panel.
    • Lift the power supply unit straight up to remove it from the back panel.

終わりに

To reassemble your device, follow these instructions in reverse order.

Jose Carrillo

メンバー登録日: 2012年09月26日

23 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 16-56, Forte Fall 2012 Cal Poly, Team 16-56, Forte Fall 2012人のメンバー

CPSU-FORTE-F12S16G56

5 メンバー

7のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 540