Skip to main content

はじめに

This guide can be used for those that are experiencing difficulties with their hold switch. A major sign of a faulty hold switch is being incapable of turning on the device. Use this guide to replace a faulty hold switch.

  1. Remove the battery compartment cover.
    • Remove the battery compartment cover.

    • Remove the battery.

  2. Locate and remove the screw next to the battery compartment lid.
    • Locate and remove the screw next to the battery compartment lid.

  3. Locate the interlocking pegs along the seam of the device's casings.
    • Locate the interlocking pegs along the seam of the device's casings.

    • Gently pry the pegs apart one at a time, working your way around the case.

    • Be careful when prying apart the pegs: they are made of plastic and may break.

  4. The battery contact springs may prevent the case from separating.
    • The battery contact springs may prevent the case from separating.

    • Push the battery contact springs down through the hole in the case.

  5. The casing protecting the USB and headphone jacks must be removed.
    • The casing protecting the USB and headphone jacks must be removed.

    • Locate and gently pry apart the two interlocking clips holding it in place.

    • The outer casings may now be removed and the MP3 player should separate.

  6. MacBook Battery 修理キット

    最低価格 $69.99

    Buy Now

    MacBook Battery 修理キット

    最低価格 $69.99

    Buy Now
  7. You now have access to all components found on the inside of the device!
    • You now have access to all components found on the inside of the device!

  8. Locate hold switch on motherboard.
    • Locate hold switch on motherboard.

  9. Locate where hold switch is connected to motherboard via soldered connections.
    • Locate where hold switch is connected to motherboard via soldered connections.

  10. Use the soldering iron to liquefy the solder connecting the hold switch to the motherboard.
    • Use the soldering iron to liquefy the solder connecting the hold switch to the motherboard.

  11. The solder and soldering iron will be very hot at this time. Do not touch unless wearing protective gloves as you will be burnt.
    • The solder and soldering iron will be very hot at this time. Do not touch unless wearing protective gloves as you will be burnt.

    • Be sure to always elevate the hot end of the soldering iron on a metal stand to prevent incidental burns.

  12. With the soldered points liquefied, remove faulty hold switch from the motherboard.
    • With the soldered points liquefied, remove faulty hold switch from the motherboard.

    • To do this liquefy the solder on each contact and remove them individually.

  13. Replace faulty hold switch with a new one.
    • Replace faulty hold switch with a new one.

  14. There may be some solder in the way of the hold switch's metal contacts. If this occurs simply melt/remove the solder to create room for the contacts.
    • There may be some solder in the way of the hold switch's metal contacts. If this occurs simply melt/remove the solder to create room for the contacts.

  15. With the new hold switch in place, use the soldering iron and solder to create a stable connection between the motherboard and hold switch.
    • With the new hold switch in place, use the soldering iron and solder to create a stable connection between the motherboard and hold switch.

    • Be sure to allow the new solder to cool and harden.

まとめ

To reassemble your device, follow these instructions in reverse order.

James Thorne

メンバー登録日: 2013年11月05日

625 ポイント

6のガイドは作成済み

チーム

UMass Dartmouth, Team 1-8, Shastany Fall 2013 UMass Dartmouth, Team 1-8, Shastany Fall 2013人のメンバー

UMASSD-SHASTANY-F13S1G8

3 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 413