メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

The back cover holds the screen in place and protects the internal components of the camera.

パーツ

パーツは指定されていません。

  1. Push the rubber viewfinder grip upward. Push the rubber viewfinder grip upward.
    • Push the rubber viewfinder grip upward.

  2. Use the Phillips #00 screwdriver to remove one 6.4 mm screw in the center of the dial. Remove the dial by lifting upward with your fingers.
    • Use the Phillips #00 screwdriver to remove one 6.4 mm screw in the center of the dial.

    • Remove the dial by lifting upward with your fingers.

  3. Use the Phillips #00 screwdriver to remove the four 5.5 mm screws surrounding the viewfinder. Use your fingers to lift the plastic viewfinder cover upward. Use your fingers to lift the plastic viewfinder cover upward.
    • Use the Phillips #00 screwdriver to remove the four 5.5 mm screws surrounding the viewfinder.

    • Use your fingers to lift the plastic viewfinder cover upward.

  4. 全てのタブを開く

    Mac用RAMアップグレードキット

    キット商品を見る

    どれだけタブを開いても
    十分に足りるRAM容量

    キット商品を見る
  5. Use the Phillips #00 screwdriver to remove the two 5.5 mm screws from the right side of the camera above the SD card port. Use the Phillips #00 screwdriver to remove the two 5.5 mm screws from the right side of the camera above the SD card port.
    • Use the Phillips #00 screwdriver to remove the two 5.5 mm screws from the right side of the camera above the SD card port.

  6. Use the Phillips #00 screwdriver to remove one 5.5 mm screw on the left, above the HDMI port.
    • Use the Phillips #00 screwdriver to remove one 5.5 mm screw on the left, above the HDMI port.

  7. Use the Phillips #00 screwdriver to remove the five 5.5 mm screws from the bottom, near the battery compartment.
    • Use the Phillips #00 screwdriver to remove the five 5.5 mm screws from the bottom, near the battery compartment.

    • Use the Phillips #00 screwdriver to remove one 3.8 mm screw from the bottom of the hand grip, below the battery compartmen.

  8. Use a plastic opening tool to separate the back cover from the front cover. Pry the back cover in this order: bottom, right side, left side. Pry the back cover in this order: bottom, right side, left side.
    • Use a plastic opening tool to separate the back cover from the front cover.

    • Pry the back cover in this order: bottom, right side, left side.

  9. Use your fingers to pull the back cover away from the front cover. Do not completely separate the back cover from the front cover as two cables hold these components together.
    • Use your fingers to pull the back cover away from the front cover.

    • Do not completely separate the back cover from the front cover as two cables hold these components together.

  10. Use tweezers to pull the two ribbon cables horizontally out of their clips. Use tweezers to pull the two ribbon cables horizontally out of their clips. Use tweezers to pull the two ribbon cables horizontally out of their clips.
    • Use tweezers to pull the two ribbon cables horizontally out of their clips.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Hannah Patrick

メンバー登録日: 2016年02月24日

855 ポイント

6のガイドは作成済み

チーム

USF Tampa, Team 1-4, Leahy Spring 2016 USF Tampa, Team 1-4, Leahy Spring 2016人のメンバー

USFT-LEAHY-S16S1G4

3 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 5

今までの合計 566