メインコンテンツにスキップ
  1. Slide the lock towards the middle of the camera, in the same direction of the arrow.
    • Slide the lock towards the middle of the camera, in the same direction of the arrow.

  2. Push the blue battery holder up in the direction of the arrow.
    • Push the blue battery holder up in the direction of the arrow.

  3. Pull the battery out of the battery slot.
    • Pull the battery out of the battery slot.

  4. Use tweezers to remove the four rubber screw covers. Use tweezers to remove the four rubber screw covers.
    • Use tweezers to remove the four rubber screw covers.

  5. Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver. Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.
    • Remove the four Phillips 2.381 mm screws on back side of camera and one Phillips 2.381 mm screw on the bottom of the camera, using a Phillips #00 screwdriver.

  6. Remove the back casing by just carefully pulling the casing off of the camera.
    • Remove the back casing by just carefully pulling the casing off of the camera.

  7. Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.
    • Use the Phillips #00 screw driver to remove the four 2.381 mm screws next to the screen hinge.

  8. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now
  9. Use plastic opening tool to disconnect screen connector from the control board.
    • Use plastic opening tool to disconnect screen connector from the control board.

  10. Remove the old screen.
    • Remove the old screen.

  11. Remove the 2.381 mm screw with a Phillips #00 screwdriver.
    • Remove the 2.381 mm screw with a Phillips #00 screwdriver.

  12. Use the plastic opening tool to remove the silver metal lens cover.
    • Use the plastic opening tool to remove the silver metal lens cover.

  13. Use the tweezers to remove the black electrical tape covering the copper connector to the control board.
    • Use the tweezers to remove the black electrical tape covering the copper connector to the control board.

  14. From the front of the camera, push the lens through the back of the camer.a
    • From the front of the camera, push the lens through the back of the camer.a

  15. Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors. Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.
    • Use a pair of tweezers to flip up the black retaining bar on each of the two ZIF connectors.

  16. Remove the lens assembly from the camera. Remove the lens assembly from the camera.
    • Remove the lens assembly from the camera.

  17. Remove the 2.381 mm screw that is holding the copper to the control board with a Phillips #00 screw driver.
    • Remove the 2.381 mm screw that is holding the copper to the control board with a Phillips #00 screw driver.

  18. Use tweezers to pull copper connector from the control board.
    • Use tweezers to pull copper connector from the control board.

  19. Use the plastic opening tool to pry the control board up, thus allowing the flash bulb assembly to be removed.
    • Use the plastic opening tool to pry the control board up, thus allowing the flash bulb assembly to be removed.

  20. Beginning with the battery on the side, gently pull upwards to remove the entire flash bulb assembly.
    • Beginning with the battery on the side, gently pull upwards to remove the entire flash bulb assembly.

まとめ

To reassemble your device, follow these instructions in reverse order.

Justin Smith

メンバー登録日: 2015年03月03日

95 ポイント

1ガイドが承認済み

チーム

Sam Houston State, Team 13-2, Blackburne Winter 2015 Sam Houston State, Team 13-2, Blackburne Winter 2015人のメンバー

SHSU-BLACKBURNE-W15S13G2

3 メンバー

4のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 1

今までの合計 143