メインコンテンツにスキップ

Samsung Galaxy Watch Active2 Back Cover Replacement

必要な工具と部品

  1. Samsung Galaxy Watch Active2 Back Cover Replacement, Turn off the watch: 手順 1、 2の画像 1 Samsung Galaxy Watch Active2 Back Cover Replacement, Turn off the watch: 手順 1、 2の画像 2
    • Turn off the Galaxy Watch Active2 by pushing and holding the bottom button for approximately 3 seconds. You should feel a short vibration.

    • When the "Power off" symbol appears, tap the center of the screen to make it shut down. You should feel a longer vibration for confirmation.

  2. Samsung Galaxy Watch Active2 Back Cover Replacement, Remove the rear screws: 手順 2、 1の画像 1
    • Use a Tri-point Y00 screwdriver to remove the four 4 mm-long screws on the back of the watch.

  3. Samsung Galaxy Watch Active2 Back Cover Replacement, Separate the back cover from the housing: 手順 3、 3の画像 1 Samsung Galaxy Watch Active2 Back Cover Replacement, Separate the back cover from the housing: 手順 3、 3の画像 2 Samsung Galaxy Watch Active2 Back Cover Replacement, Separate the back cover from the housing: 手順 3、 3の画像 3
    • Use an opening pick and place it between the plastic back cover and the metal housing near the buttons.

    • Push the opening pick into the gap to separate the back cover from the housing.

    • Don’t remove the back cover all the way yet. There is a cable connecting it to the motherboard.

  4. Samsung Galaxy Watch Active2 Back Cover Replacement, Disconnect the sensor array: 手順 4、 2の画像 1 Samsung Galaxy Watch Active2 Back Cover Replacement, Disconnect the sensor array: 手順 4、 2の画像 2
    • Carefully lift the back cover to access the sensor array connector.

    • Use a spudger to disconnect the sensor array from the motherboard.

  5. Samsung Galaxy Watch Active2 Back Cover Replacement, Remove the back cover: 手順 5、 1の画像 1
    • Remove the back cover.

終わりに

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

9 の人々がこのガイドを完成させました。

Tobias Isakeit

メンバー登録日: 03/31/14

117,289 ポイント

188のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

322 メンバー

2,521のガイドは作成済み

5 件のコメント

What kind of glue would you use if the plastic of the back cover fell off?

Dave Hains - 返信

This happened to me as well. I opted to replace the entire adhesive-attached back cover. You can find kits that include a new back with a new adhesive gasket already attached. You just need to take off the old one and make sure it's clean before putting on the new one. I bought this one on ebay: https://www.ebay.com/itm/164638316825

John S. -

Hello. Where can i get the back cover with adhesive as a replacement or just the adhesvie? I noticed it is a weird rubbery glue and i cannot source this anywhere.

Arbuzov Paul - 返信

What kind of glue would you use if the plastic of the back cover fell off

Ilona Smit - 返信

Why would you use glue? The back is fixed with screws.
If there is a loose part on the back cover you might want to try a glue like the E6000, B7000 or T9000 (there are different combinations out there)

Tobias Isakeit -

コメントを追加

統計データ:

過去 24時間: 26

過去 7 日: 147

過去 30 日: 603

今までの合計 32,379