この翻訳は、ソースガイドの最新の更新を反映していない可能性があります。 翻訳の更新に協力してください。 または ソースガイドを参照してください。
はじめに
このガイドを参照して、Samsung Galaxy Note8のバックカバーを交換します。
バッテリーが膨張している場合、デバイス本体を加熱しないでください。 必要に応じて、スポイトもしくはシリンジを使用して、背面カバーの端にイソプロピルアルコール(濃度90%以上)を注入して、接着剤を弱めます。 バッテリーが膨張すると、非常に危険な場合があるため、目のプロテクターを着用して十分な注意を払うか、手順がわからない場合は専門家に相談してください。
デバイスを開口すると、防水用シーリングにダメージが入ってしまいます。 接着シールを交換しない場合は、デバイスは通常通り機能しますが、防水性能を失っていますのでご注意ください。
バックカバーを装着するには交換用の接着剤が必要です。
必要な工具と部品
-
-
スマートフォンの電源を切ります。
-
Note8の裏面に留められた接着剤を柔らかくするために、iOpenerを用意します。
-
電源ボタンの側面に沿って、Note8の裏面にiOpenerを置きます。
-
-
-
吸盤ハンドルを使ってバックカバーを持ち上げて、生じた隙間に開口ピックを差し込みます。
-
デバイス横の中央部分から作業を始めて、吸盤ハンドルを引き上げながら、ピックで接着剤を切開します。
-
開口ピックを下側コーナーに向けて動かし、接着剤がケースに再装着しないよう、その場に残しておきます。
-
別の開口ピックを使って上部コーナーまで移動します。
I used an X-acto knife with the flat blade to get it started. I tried using the suction cup - but it’s difficult to get good leverage. Once I got the cover started - I used the metal pry tool (sharpened with a dremel file) and a business card to work it open.
This is definitely the hardest part.
Once off I see all the glue on the curved part of the chassis NOTON THE BACK. Apply heat to curved edges.
Lyle Walsh - 返信
-
-
-
この手順は未翻訳です。 翻訳を手伝う。
-
When the adhesive has been separated on all three sides properly you will be able to slowly lift the back cover.
-
Pay attention to the fingerprint sensor connector when flipping the back cover open. You might need to disconnect it as described in the next step.
I broke the back camera cover for the NUT 8 and then I bought a commercial cover and installed it but the quality of the picture became very bad and my question is, do you know where to get the original cover at a reasonable price?
-
-
-
ピンセットを使って、指紋センサーの接続を外します。
don't skip disconnecting the sensor, even if isn't still glued to the case. it has to move away from the NFC/charging coil assembly in order to free the latter so it can be lifted away from the battery.
-
-
-
バックカバーを取り外します。
How do you swap the fingerprint sensor
Lukus Carr - 返信
You can use a tweezer to swap the fingerprint sensor, you might be careful when doing the step 6, additionally, a tweezer will be helpful when reassemble the fingerprint sensor. please note that your new back cover needs to have the fingerprint adhesive on. most of the product did not have. i have get a LUVSS brand from amazon which came with all OEM adhesive and full set tools, even a B6000 glue, best option to go for replacing the note 8 back glass
-
可能であれば、デバイスの電源を入れて、新しいパーツのテストを行ってから接着剤をインストールして密封してください。
プレカットされた接着剤もしくは両面テープで新しいバックカバーを固定します。
デバイスを再組み立てする際は、これらのインストラクションを逆の順番に従って作業を進めてください。
リアカバーのインストールが終了したら、強くて一定のプレッシャーをデバイスに数分間与えます。接着剤をしっかりと固定させてください。重量のある本を上に置くと効果的です。
可能であれば、デバイスの電源を入れて、新しいパーツのテストを行ってから接着剤をインストールして密封してください。
プレカットされた接着剤もしくは両面テープで新しいバックカバーを固定します。
デバイスを再組み立てする際は、これらのインストラクションを逆の順番に従って作業を進めてください。
リアカバーのインストールが終了したら、強くて一定のプレッシャーをデバイスに数分間与えます。接着剤をしっかりと固定させてください。重量のある本を上に置くと効果的です。
42 の人々がこのガイドを完成させました。
以下の翻訳者の皆さんにお礼を申し上げます:
72%
これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 あなたも貢献してみませんか?
翻訳を始める ›
3 件のコメント
the separate adhesive was unneeded the replacement back cover came with adhesive
So close!!!!’ I sliced the fingerprint sensor cable off, that area of the back glass was so smashed. Hopefully I can get a replacement to me by Saturday
I used a heat gun to soften the glue - worked it around the edges, moving the heat gun quickly. As this is my first attempt, I’m still calibrating on this - but other guides mention getting the back cover hot enough so as it’s just too hot to touch. I also have a temp probe on my multi-meter, and I measured appx. 75 deg. C.
One of the other guides showed using a electronics hot plate set to 105 deg C for 60 sec.
Phil Brooks - 返信