危険
潜在的な危険
この手順に正しく従わない場合は損傷が生じる可能性があります。ご注意のうえ使用し、すべての警告に従ってください。
危険
  1. Flip the phone over and use your fingernail or an opening tool to remove the back cover.
    • Flip the phone over and use your fingernail or an opening tool to remove the back cover.

    コメントを追加する

  2. Remove the battery.
    • Remove the battery.

    • If your phone has a SIM card or MicroSD card, remove them.

    コメントを追加する

    • Remove the 9 Philips #00 screws (marked in red)

    コメントを追加する

    • Use an opening pick to pry off the mid frame.

    コメントを追加する

  3. Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    • Disconnect the following ribbon cables from the motherboard:

      • The digitizer and LCD assembly

      • Headphone Jack and Earpiece

      • Daughter board flex cable.

      • Antenna connector

    コメントを追加する

    • Use a plastic opening tool to remove the motherboard.

    コメントを追加する

    • Remove 1 Phillips screw

    • Remove the daughterboard.

    • The flex cable is glued, so exercise extreme caution, as excessive force can damage the cable.

    コメントを追加する

    • Use an opening pick to remove the audio jack.

    コメントを追加する

    • Disconnect digitizer

    コメントを追加する

    • Push the speaker outwards so as it is released.

    コメントを追加する

    • Use a heat gun or an iOpener to heat the digitizer and soften the glue securing it.

    • Use an opening pick to break up the glue around the edges of the digitizer.

    • You may apply more heat if needed.

    • Remove the digitizer and any broken glass.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

86 の人々がこのガイドを完成させました。

ivan coene

メンバー登録日: 2014年03月12日

2,958 ポイント

2のガイドは作成済み

yes, but where can I buy the screen replacement?

Roxannie - 返信

I bought it on Ebay...

ivan coene - 返信

Comment root galaxy core prime g361f android 5.1.1

soulaemen - 返信

Follow the instructions in reverse order? Do you need glue for the new screen? What kind of glue? How is it applied?

Thomas McGuigan - 返信

Nor do they show how the new digitizer plugs in...

chris smith -

Magkano po ang magagastos lcd and touch po ung papalitan

ramil cariaga - 返信

Is the Potentially Dangerous part when you work with the glass? Just curious if there was some other hidden danger?

Sara - 返信

Jup, it's only because you work with broken glass ;)

ivan coene -

I have 2 devicies.

#1 broken LCD+digi

#2 dead with fine LCD+digi

Can I swap whole screen (LCD+digi) together with frame?

Piotr Jaremko - 返信

Never tried, but i guess you could just stop at step 9...

Let me know if it worked

ivan coene -

I own and use a core prime as my phone, it has a shattered screen, verizon wont replace it because it was a warrentty replacement for my kyocera brigadir that i dropped in the ocean, it works again btw just a bit slower, but i cant afford a new phone, and i cant deal with the glass splinters any more, i dont want to spend more then i have to, are some of these required things actually needed? Like the seperation tools, can i do the same thing with say an automotive trim tool(already have one)? It looks similar at the prying tip. Maybe a high end hair dryer instead of a heat gun? (My gf has one i can use). My true goal is to spend only the cost of the replacement parts, as i do not currently have a steady income. Thanks in advance for any advise.

S1l3ntb0b696 - 返信

コメントを追加する

統計データを表示:

過去 24時間: 8

過去 7 日: 56

過去 30 日: 244

今までの合計 113,162