修理を始めるには コミュニティ ストア

SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement

医療機器
この修理ガイドは医療機器メーカーからの是認を得ておらず、iFixitと医療機器メーカーは提携していません。

はじめに

For more information on replacing the main circuit board, please refer to page 25 in the service manual.

必要な工具と部品

  1. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement, How to Open and Close Housing (SOMNOcomfort and SOMNObalance Ventilator): 手順 1、 1の画像 1

    • Remove the covering cap. (pg. 23)

    翻訳

  2. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 2、 1の画像 1

    • Place the unit upside down on a non-slip surface and remove the six screws. (pg. 23)

    翻訳

  3. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 3、 1の画像 1

    • Remove the lower part of the housing with a swiveling motion away to the side. Note the SOMNOcomfort series uses a shorter circuit board than the balance series ventilator. (pg. 23)

    翻訳

  4. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 4、 3の画像 1 SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 4、 3の画像 2 SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 4、 3の画像 3

    • Remove the connector (X1) from the circuit board.

    • Pull the connecting cable (64) from its mount.

    • Now set aside the lower part of the housing. (pg. 23)

    翻訳

  5. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 5、 2の画像 1 SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 5、 2の画像 2

    • Next, how to close the compartment and reverse the process.

    • Hold the lower part of the housing to the upper part at an angle

    • Attach the connector (X1) to the main circuit board. When doing so the connector’s nub has to point towards the lock. (pg. 24)

    翻訳

  6. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 6、 2の画像 1 SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 6、 2の画像 2

    • Properly align the main circuit board inside the unit.

    • Attach the connecting cable (64) to its mount (pg. 24)

    翻訳

  7. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 7、 1の画像 1

    • Place the lower part of the housing on the upper part (47). Please make sure the main circuit board (44) is aligned properly, and that the connecting cable (64) is not being squeezed anywhere. (pg. 24)

    翻訳

  8. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 8、 1の画像 1

    • Now reattach the upper part of the housing by tightening the six screws. (pg. 24)

    翻訳

  9. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 9、 1の画像 1

    • Insert the covering cap. (pg. 24)

    翻訳

  10. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement, Main Circuit Board: 手順 10、 1の画像 1

    • Pull the plug X200 and X400 from the main circuit board.

    翻訳

  11. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 11、 1の画像 1

    • Remove the flat cables from front panel foil and display: To do so, pull the lock. Once you have pulled the lock, you can remove the flat cable.

    翻訳

  12. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 12、 1の画像 1

    • Remove pressure measurement tube 45 from the pressure sensor or pull out the tube adapter of the pressure measurement tube.

    翻訳

    • Remove the main circuit board 44.

    翻訳

  14. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 14、 1の画像 1

    • Attach tube 45 to the pressure sensor of a new main circuit board 44 or connect the tube adapter of the pressure measurement tube to the angular bush on the pressure sensor.

    翻訳

  15. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 15、 1の画像 1

    • Reattach the flat wires of front panel foil and display to the main circuit board: – Pull the lock. – Insert the flat cable into the connector. – Push the lock back in.

    翻訳

  16. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 16、 1の画像 1

    • Connect plugs X200 and X400 to the main circuit board.

    翻訳

  17. SOMNOcomfort and SOMNObalance Ventilator Main Circuit Board Replacement: 手順 17、 1の画像 1

    • Close the unit

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

2人の作成者と共同で作成されました。

Brandon Yowakim

メンバー登録日: 01/18/18

1,182 ポイント

2のガイドは作成済み

バッジ: 10

+7 個以上のバッジ

チーム

Cal Poly, Team S1-G3, Zimmerman Spring 2020 Cal Poly, Team S1-G3, Zimmerman Spring 2020人のメンバー

CPSU-ZIMMERMAN-S20S1G3

5 メンバー

10のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 3

今までの合計 187