メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

The motherboard is a piece of circuitry that serves as the device's circuit board. The primary internal parts of the Roku 4 are all attached to the motherboard. This disassembly guide will serve as the core to further internal disassembly, as you will be able to fix other parts from here.

  1. Place the Roku 4 face-down on a table. The rubber sticker should be facing you.
    • Place the Roku 4 face-down on a table. The rubber sticker should be facing you.

  2. Starting at one corner of the device, pull the rubber sticker back toward the opposite corner of the device carefully to reveal the underlying screws.
    • Starting at one corner of the device, pull the rubber sticker back toward the opposite corner of the device carefully to reveal the underlying screws.

    • Completely remove the rubber sticker to reveal the underlying screws on the device.

    • Place the rubber sticker facing up on the table to preserve its adhesiveness. It will be needed to reassemble the device.

  3. Turn the Phillips PH1 screwdriver counterclockwise to unscrew all 4 of the 12.0 mm screws.
    • Turn the Phillips PH1 screwdriver counterclockwise to unscrew all 4 of the 12.0 mm screws.

    • Store the screws in a safe place, such as on a magnetic project mat, so they do not get lost before reassembly.

  4. Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits

    Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits
  5. Turn the device over so you can see the "4" on the top cover. Turn the device over so you can see the "4" on the top cover.
    • Turn the device over so you can see the "4" on the top cover.

  6. Wedge a plastic opening tool into the seam between the top cover and bottom casing of the device and create a gap. Prying open the device is quite difficult and requires a large amount of force.  Use caution to avoid breaking the device or hurting yourself.
    • Wedge a plastic opening tool into the seam between the top cover and bottom casing of the device and create a gap.

    • Prying open the device is quite difficult and requires a large amount of force. Use caution to avoid breaking the device or hurting yourself.

  7. After you have created a gap large enough to fit your fingers between, gently lift up the top cover to open the device and reveal the motherboard.
    • After you have created a gap large enough to fit your fingers between, gently lift up the top cover to open the device and reveal the motherboard.

    • The motherboard should still be attached to the underside of the top cover by a red wire, a blue wire, and a black wire.

  8. To begin removing the motherboard from the plastic casing, pinch the black plastic clip and gently pull upward. Once you feel the motherboard begin to loosen from the plastic casing, pull it upward to remove it completely. The motherboard should still be attached to the underside of the top cover by a red wire, a blue wire, and a black wire.
    • To begin removing the motherboard from the plastic casing, pinch the black plastic clip and gently pull upward.

    • Once you feel the motherboard begin to loosen from the plastic casing, pull it upward to remove it completely.

    • The motherboard should still be attached to the underside of the top cover by a red wire, a blue wire, and a black wire.

  9. Peel back the black adhesive strip that attaches the blue wire to the motherboard. Repeat this step for the strip that attaches the black and red wires to the motherboard. Repeat this step for the strip that attaches the black and red wires to the motherboard.
    • Peel back the black adhesive strip that attaches the blue wire to the motherboard.

    • Repeat this step for the strip that attaches the black and red wires to the motherboard.

  10. Using a soldering iron, desolder the blue, red, and black wires from the motherboard. Consult iFixit's Soldering Skills guide to safely use the soldering iron. The motherboard should now be completely disconnected from the top cover of the device.
    • Using a soldering iron, desolder the blue, red, and black wires from the motherboard.

    • Consult iFixit's Soldering Skills guide to safely use the soldering iron.

    • The motherboard should now be completely disconnected from the top cover of the device.

終わりに

Follow these steps in the reverse order to reassemble your device.

2 の人々がこのガイドを完成させました。

Bradley Rains

メンバー登録日: 2017年03月26日

121 ポイント

1ガイドが承認済み

チーム

Baylor, Team S5-G4, Williams Spring 2017 Baylor, Team S5-G4, Williams Spring 2017人のメンバー

BU-WILLIAMS-S17S5G4

3 メンバー

4のガイドは作成済み

コメント1件

Thank you, have you upgraded to a new 2019 Ultra model yet?

Allan Landwer - 返信

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 8

過去 30 日: 50

今までの合計 2,887