はじめに

How to remove and replace the hard drive.

Remove the 7 mm Philip screws.
  • Remove the 7 mm Philip screws.

  • Remove the 10 mm Philip screws.

  • Remove the 14 mm Philip screw.

コメントを追加する

Open the flap on the left hand side. Open the flap on the left hand side.
  • Open the flap on the left hand side.

コメントを追加する

Insert the iPod opening tools between the right and left sides of the latch. Pry the right side  of the latch, and then pry the left side to detach the laptop's cover.
  • Insert the iPod opening tools between the right and left sides of the latch.

  • Pry the right side of the latch, and then pry the left side to detach the laptop's cover.

コメントを追加する

Open the flap on the right side. Open the flap on the right side.
  • Open the flap on the right side.

コメントを追加する

Insert the iPod opening tools towards the right side of the latch.
  • Insert the iPod opening tools towards the right side of the latch.

  • Gently pry the right side out to release the top cover.

コメントを追加する

Lift the keyboard slowly. A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.
  • Lift the keyboard slowly.

  • A cable connects the keyboard to the motherboard. If you are not careful, you will damage the cable.

コメントを追加する

Use your fingers or a spudger to detach the connector.
  • Use your fingers or a spudger to detach the connector.

コメントを追加する

Carefully lift and remove the keyboard. Carefully lift and remove the keyboard.
  • Carefully lift and remove the keyboard.

コメントを追加する

On the back of the computer, use a Flathead screwdriver to remove this lone screw.
  • On the back of the computer, use a Flathead screwdriver to remove this lone screw.

コメントを追加する

After the screw is out, gently remove the cover. After the screw is out, gently remove the cover.
  • After the screw is out, gently remove the cover.

コメントを追加する

Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver. Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.
  • Turn the computer back over so the hard drive faces up. Remove the shown screw with a Phillips screwdriver.

コメントを追加する

Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.
  • Make sure you are grounded and detach the IDA cable connecting the hard disk to the motherboard.

コメントを追加する

Remove the final two screws (shown) and slide out the hard drive. Remove the final two screws (shown) and slide out the hard drive.
  • Remove the final two screws (shown) and slide out the hard drive.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Derek Driscoll

メンバー登録日: 2010年04月15日

110 ポイント

16のガイドは作成済み

チーム

Cal Poly, Team 26-27, Regan Spring 2010 Cal Poly, Team 26-27, Regan Spring 2010人のメンバー

CPSU-REGAN-S10S26G27

3 メンバー

18のガイドは作成済み

コメント1件

You don't have to go to this length to remove the hard drive on a 560Z. Only do steps 0 (remove battery), 9 (remove screw) and 10 (remove cover). Then simply grab the blue tab of the hard drive caddy and pull the drive out of the bay. Complete directions on maintenance of the IBM Thinkpad 560Z can be found here:

http://www.thinkpads.com/support/hmm/hmm...

The Hardware Maintenance Manual has all of the information you need to take a 560Z apart and put it back together.

The procedure outlined here is similar to what the 560, 560E and 560X systems required; the 560Z is totally different when removing the hard drive.

Raymond - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 6

今までの合計 2,477