はじめに

How to replace speaker

Turn the phone over so that the screen is facing the work surface
  • Turn the phone over so that the screen is facing the work surface

コメントを追加する

Press your thumb against the battery latch. While pressing on latch, slide off battery cover towards the bottom of the phone.
  • Press your thumb against the battery latch. While pressing on latch, slide off battery cover towards the bottom of the phone.

  • You may need to apply considerable force on the latch at the bottom of the phone to complete this successfully.

コメントを追加する

Remove the battery by pushing downward on the area where prongs connect to bottom inside of the phone while using a thumb, finger, or tool to pull on the top of the battery to lift it out.
  • Remove the battery by pushing downward on the area where prongs connect to bottom inside of the phone while using a thumb, finger, or tool to pull on the top of the battery to lift it out.

コメントを追加する

Using the T6 Torx screwdriver, remove the bottom two screws on the back of the phone.
  • Using the T6 Torx screwdriver, remove the bottom two screws on the back of the phone.

コメントを追加する

MacBook Battery Fix Kits
Fix Kits Starting at $69.99
MacBook Battery Fix Kits
Starting at $69.99
Remove speaker phone cover by unsecuring the two latches on the edge close to top of the phone with the plastic opening tool.
  • Remove speaker phone cover by unsecuring the two latches on the edge close to top of the phone with the plastic opening tool.

コメントを追加する

Detach the speaker phone cover by pulling up on the bottom of the speaker phone cover.
  • Detach the speaker phone cover by pulling up on the bottom of the speaker phone cover.

  • As you detach the speaker phone cover you will notice a sticky glue sealing the rubber gasket from the cover to the speaker mesh. This is normal and will correctly reset the first few times the pieces are separated.

コメントを追加する

Remove top two screws with T6 Torx screw driver, from the back of phone.
  • Remove top two screws with T6 Torx screw driver, from the back of phone.

コメントを追加する

Turn the phone sideways and unlatch the hinge on one side of the phone by pushing inwards and twisting to the side with the plastic opening tool.
  • Turn the phone sideways and unlatch the hinge on one side of the phone by pushing inwards and twisting to the side with the plastic opening tool.

コメントを追加する

You should now be able to easily separate the phone into two pieces. The battery prong may fall out when the separation occurs, just don't loose it!
  • You should now be able to easily separate the phone into two pieces.

  • The battery prong may fall out when the separation occurs, just don't loose it!

コメントを追加する

Set aside the bottom part of the phone.
  • Set aside the bottom part of the phone.

  • Drop out the rubber keypad from the top, so that it does not get in the way.

コメントを追加する

Use the plastic separator tool to apply significant pressure in a downward motion on the top of the white speaker unit.
  • Use the plastic separator tool to apply significant pressure in a downward motion on the top of the white speaker unit.

コメントを追加する

The speaker unit should become loose.
  • The speaker unit should become loose.

  • You can now push the separating tool beneath the speaker and pop it out.

  • Once the defective unit is removed, pop your new speaker unit back into place.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Sean Tiernan

メンバー登録日: 2010年01月20日

5 ポイント

5のガイドは作成済み

チーム

Cal Poly, Team 3-16, Maness Winter 2010 Cal Poly, Team 3-16, Maness Winter 2010人のメンバー

CPSU-MANESS-W10S3G16

4 メンバー

5のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 1,080