First remove the rear case/battery cover
  • First remove the rear case/battery cover

コメントを追加する

Remove the battery.
  • Remove the battery.

  • Remove the two T5 Torx screws.

  • Prise off the lower casing towards the right in the picture, taking care not to break the two tabs

コメントを追加する

  • Remove the two further T5 torx screws

  • Remove the three Phillips #00 screws.

コメントを追加する

  • Now carefully prise off the case all round and it will detach completely

コメントを追加する

  • Prise up this connector

コメントを追加する

  • And this one

コメントを追加する

  • Lift up the retainer using a plastic opening tool.

コメントを追加する

  • And carefully pull out the tab connector.

  • NOW PAUSE WITHOUT MOVING ANYTHING!

コメントを追加する

  • NOTE THIS FLEXIBLE RIBBON

コメントを追加する

  • Carefully lift up the board from the left-hand side allowing it to 'hinge' on the metallic ribbon connector you have just noted and allow it to lay flat

Is this a HTC Wildfire S or Wildfire?

Andre Quintana - 返信

That's not HTC Wildfire S.

It's the previous model HTC Wildfire.

Billy Loizos - 返信

Is this wildfire a 3333 or wildfire s?

paul - 返信

  • The freed connector for the screen should have unfolded

  • Now the screen can be pried from the outer case, but take care as you do so not to tear the metallic ribbon between the two casings

コメントを追加する

  • To detach the screen it can help to use a pry tool to push the screen from behind through the slot

コメントを追加する

  • The screen is detached and the connector can be wiggled out through the slot

コメントを追加する

  • Remove the old screen and connector altogether

コメントを追加する

  • The connector for the new screen now has to be wiggled back through the slot

コメントを追加する

  • Once the connecter is pushed through the slot, you should now stick the new screen into place using suitable adhesive strip

コメントを追加する

  • Fold down the ribbon connector from the screen and carefully fold the two casing halves together again, making sure that the two connectors are sticking out of the side

コメントを追加する

  • Reconnect the two connectors on the right hand side by pressing down

コメントを追加する

  • Reinsert the ribbon connector on the left hand side and push down the retaining catch

コメントを追加する

  • Clip the rear casing back on to the body

コメントを追加する

  • Put the bottom cover back in place and then replace all the screws

コメントを追加する

  • Replace battery and battery cover and all should now be well!

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

Mikey Willbiscuit

メンバー登録日: 2013年05月13日

480 ポイント

1ガイドが承認済み

コメント1件

Nice detailing of the teardown steps but the phone shown here is a regular HTC Wildfire (HTC G8) and not the latter HTC Wildfire S (HTC G13). Apparently, the orignal Wildfire has two variants (A3333 and A310e). Each variant uses a different digitizer (the touch glass panel on top of the actual LCD). If you need to buy a replacement digitizer, verify if your variant has an IC on the digitizer ribbon cable or not. On my phone, the shattered original digitizer had no IC on the ribbon and when I replaced it with one that had one, the phone wouldn’t recognize the touch inpupts.

Jeremy - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 14

今までの合計 11,279