はじめに

You will be removing some leather grips, which you will reuse, to access some screws. Be careful not to tear these grips.

パーツ

パーツは必要ありません。

Flip the camera so that the bottom is facing you. Take a spare coin and unscrew the battery cover off.
  • Flip the camera so that the bottom is facing you.

  • Take a spare coin and unscrew the battery cover off.

コメントを追加する

Remove the batteries, making sure to note their proper alignment.
  • Remove the batteries, making sure to note their proper alignment.

コメントを追加する

Remove two 4.8mm screws. Remove one 3.4mm screw.
  • Remove two 4.8mm screws.

  • Remove one 3.4mm screw.

  • Remove one 2.65mm screw.

  • Lift off the back cover.

コメントを追加する

Remove three 3.5mm screws.
  • Remove three 3.5mm screws.

  • Remove two 3.8mm screws.

  • Remove one 6.35mm screw.

  • Remove one 4mm screw. Lift off the disk.

  • Remove one 5.11mm screw.

コメントを追加する

Lift up the silver, metal piece
  • Lift up the silver, metal piece

  • Please note that some internal pieces may come loose during this process.

コメントを追加する

Remove four 4.45mm screws and remove the alignment ring. Remove the interior metal ring and the black plastic ring.  Pay attention to the spring's location. Pay attention to the alignment of the interior metal ring and the black plastic ring.
  • Remove four 4.45mm screws and remove the alignment ring.

  • Remove the interior metal ring and the black plastic ring. Pay attention to the spring's location.

  • Pay attention to the alignment of the interior metal ring and the black plastic ring.

The photo is wrong, the red dot should be facing north, instead of west.

Laura Ceja - 返信

Remove the two black stoppers. Using the metal spudger, remove the two triangular hangers. Using the metal spudger, remove the two triangular hangers.
  • Remove the two black stoppers.

  • Using the metal spudger, remove the two triangular hangers.

コメントを追加する

Using the metal spudger, peel off the right leather cover. Be careful not to tear the cover because you will need to use it again.
  • Using the metal spudger, peel off the right leather cover.

  • Be careful not to tear the cover because you will need to use it again.

コメントを追加する

Use the metal spudger to remove both the grip cover and the left leather cover. Be careful not to tear the covers because you will need to use them again. Be careful not to tear the covers because you will need to use them again.
  • Use the metal spudger to remove both the grip cover and the left leather cover.

  • Be careful not to tear the covers because you will need to use them again.

コメントを追加する

Remove two 5.3mm screws. Remove two 5.3mm screws.
  • Remove two 5.3mm screws.

  • Remove two 5.3mm screws.

  • Remove one 2.35mm screws.

コメントを追加する

Remove the left and right plastic covers. Remove the left and right plastic covers.
  • Remove the left and right plastic covers.

コメントを追加する

Remove two 6.65mm screws. Remove two 2.93mm screws. Remove four 5.3mm screws.
  • Remove two 6.65mm screws.

  • Remove two 2.93mm screws.

  • Remove four 5.3mm screws.

  • Remove the black plastic lens holder.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Nick

メンバー登録日: 2011年04月19日

387 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 8-7, Regan Spring 2011 Cal Poly, Team 8-7, Regan Spring 2011人のメンバー

CPSU-REGAN-S11S8G7

4 メンバー

4のガイドは作成済み

コメント1件

I have Problems to assemble the new black plastic lens holder.

The space between camera Cup and the housing is very low.

Did someone have the same Problems ?

Klaus Kohlhas - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 20

今までの合計 5,484