メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Removing HP Compaq dx2000MT Power Supply

作成者： Logan Pace (そして 2 人のその他投稿者)
  • コメント: 1
  • お気に入り: 13
  • 完了: 7

難易度

普通

手順

8

所要時間

必要時間を提案??

セクション

2

フラグ

1

Markup Mishap

間違いの指摘

このガイドは最適な校正が必要です。校正の注釈を付けたり訂正することにご協力ください。

はじめに

This guide will show you how to remove the power supply on your HP Compaq dx2000MT.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Turn off your computer and remove the power cable by pulling it straight out of its socket.

    • Turn off your computer and remove the power cable by pulling it straight out of its socket.

    翻訳

  2. Remove the two Phillips #2 screws that secure the case door to the device. Remove the two Phillips #2 screws that secure the case door to the device.

    • Remove the two Phillips #2 screws that secure the case door to the device.

    翻訳

  3. Remove the side case door by pushing towards the rear of the device with your hand. This may take considerable force so keep pushing! Once you slide the door back, remove it by pulling it outwards from the device.

    • Remove the side case door by pushing towards the rear of the device with your hand.

    • This may take considerable force so keep pushing!

    • Once you slide the door back, remove it by pulling it outwards from the device.

    翻訳

  4. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now

  5. Remove the side case door by pushing towards the rear of the device with your hand. Once again, this may take considerable force. Once you slide the door back, remove it by pulling it outwards from the device.

    • Remove the side case door by pushing towards the rear of the device with your hand.

    • Once again, this may take considerable force.

    • Once you slide the door back, remove it by pulling it outwards from the device.

    翻訳

  6. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    • Remove the 4 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    翻訳

  7. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device. Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    • Remove the 20 pin ATX power connector from the motherboard by pressing down the holding latch and pulling out towards the side of the device.

    翻訳

  8. Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply Remove the 4 Torx T15 screws from the rear of the power supply

    • Remove the 4 Torx T15 screws from the rear of the power supply

    翻訳

  9. Slide the power supply towards the front of the device Keep your hand underneath it! You don't want to drop it!

    • Slide the power supply towards the front of the device

    • Keep your hand underneath it! You don't want to drop it!

    • Then pull the power supply down and remove it from the case.

    翻訳
まとめ

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

作成者

2他の投稿者と一緒に

Logan Pace

メンバー登録日: 2011年10月12日

2,020 ポイント

9のガイドは作成済み

バッジ: 14

+11 個以上のバッジ

チーム

Cal Poly, Team 17-16, Regan Fall 2011 Cal Poly, Team 17-16, Regan Fall 2011人のメンバー

CPSU-REGAN-F11S17G16

4 メンバー

17のガイドは作成済み

0コメント

コメントを追加

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 5

過去 30 日: 17

今までの合計 2,500