はじめに

In order to perform any sort of repair on the throttle body unit, it must first be removed from the engine by following these step by step instructions

パーツ

パーツは必要ありません。

Firstly Disconnect  battery Always take the negative terminal off first.
  • Firstly Disconnect battery

    • Always take the negative terminal off first.

    • '''General Tip After disconnecting the battery leave the car for about 10 mins , This lets any residual energy left in the electrical system to dissapate. It is good practise whatever the job

コメントを追加する

Locate throttle body on right side of engine, it is between the intake tube and intake manifold.
  • Locate throttle body on right side of engine, it is between the intake tube and intake manifold.

コメントを追加する

Locate throttle linkage cable assembly.
  • Locate throttle linkage cable assembly.

コメントを追加する

Twist the assembly clockwise. Twist the assembly clockwise.
  • Twist the assembly clockwise.

コメントを追加する

Slide both slackened cables off assembly’s guides.
  • Slide both slackened cables off assembly’s guides.

コメントを追加する

Locate the two hoses on the top of the throttle body. Gently lift the hoses off.
  • Locate the two hoses on the top of the throttle body.

  • Gently lift the hoses off.

コメントを追加する

Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.
  • Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.

コメントを追加する

Remove the intake tube from the throttle body.
  • Remove the intake tube from the throttle body.

コメントを追加する

Locate wiring clip on the underside of the throttle body.
  • Locate wiring clip on the underside of the throttle body.

コメントを追加する

Press down on the locking mechanism before gently removing the wiring clip. Press down on the locking mechanism before gently removing the wiring clip.
  • Press down on the locking mechanism before gently removing the wiring clip.

コメントを追加する

Locate throttle linkage arm. Open the locking clip with a flat head screwdriver. Pry off the linkage arm with a flat head screwdriver.
  • Locate throttle linkage arm.

  • Open the locking clip with a flat head screwdriver.

  • Pry off the linkage arm with a flat head screwdriver.

コメントを追加する

Locate the three 13mm nuts attaching the throttle body to the intake manifold. Remove nuts with a 13mm crescent wrench. Remove nuts with a 13mm crescent wrench.
  • Locate the three 13mm nuts attaching the throttle body to the intake manifold.

  • Remove nuts with a 13mm crescent wrench.

コメントを追加する

Lift the throttle body off of the intake manifold.
  • Lift the throttle body off of the intake manifold.

  • The manifold is now out of the engine bay and ready for cleaning or adjustment.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Raymond

メンバー登録日: 2010年10月11日

61 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 3-28, Regan Fall 2010 Cal Poly, Team 3-28, Regan Fall 2010人のメンバー

CPSU-REGAN-F10S3G28

4 メンバー

9のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 14

今までの合計 3,542