メインコンテンツにスキップ

Protocol Galileo Stealth Motor Replacement

必要な工具と部品

  1. Protocol Galileo Stealth Motor Replacement, Propeller: 手順 1、 1の画像 1
    • Remove the chrome shaft cover by lightly pulling it away from the drone.

  2. Protocol Galileo Stealth Motor Replacement: 手順 2、 1の画像 1
    • Using a Phillips #000 screwdriver, remove the 7mm screw from the propeller stop.

    • Be sure to apply adequate pressure when removing the screw to prevent stripping it out.

  3. Protocol Galileo Stealth Motor Replacement: 手順 3、 1の画像 1
    • Remove the propeller stop from shaft by lightly pulling it away from the drone.

  4. Protocol Galileo Stealth Motor Replacement: 手順 4、 1の画像 1
    • Remove the propeller from shaft by lightly pulling it away from the drone.

  5. Protocol Galileo Stealth Motor Replacement, Housing: 手順 5、 2の画像 1 Protocol Galileo Stealth Motor Replacement, Housing: 手順 5、 2の画像 2
    • Remove the 8mm long Phillips #0 screws (24 total) from the lower housing unit.

    • Take care to place the screws in a safe place to prevent losing them.

  6. Protocol Galileo Stealth Motor Replacement: 手順 6、 1の画像 1
    • Separate the upper and lower housing units by lightly pulling the two housing units apart.

  7. Protocol Galileo Stealth Motor Replacement, Motor: 手順 7、 2の画像 1 Protocol Galileo Stealth Motor Replacement, Motor: 手順 7、 2の画像 2
    • Remove the 3 outer 8mm long Phillips #0 screws from the lower drone housing.

    • Remove the 2 inner 3 mm long Phillips #0 screws from the drone motor.

    • Place screws in a safe place to prevent misplacing them.

  8. Protocol Galileo Stealth Motor Replacement: 手順 8、 1の画像 1
    • Remove the two 6mm long Phillips #0 screws from the lower motor cover located on the underside of the drone.

    • Place the screws in a safe place to prevent misplacing them.

  9. Protocol Galileo Stealth Motor Replacement: 手順 9、 1の画像 1
    • Remove the motor cover by lightly pulling it away from the drone.

  10. Protocol Galileo Stealth Motor Replacement: 手順 10、 2の画像 1 Protocol Galileo Stealth Motor Replacement: 手順 10、 2の画像 2
    • Unclip the wire plug by applying light pressure to the wire plug with the plastic opening tool, and remove the motor.

    • This plug can be a bit difficult to remove, but it does not require much force to remove.

    • Avoid damaging the plug and wires when unclipping wire plug.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

5人の作成者と共同で作成されました。

Matthew Selting

メンバー登録日: 02/15/18

432 ポイント

4のガイドは作成済み

チーム

UW Stout, Team S8-G4, Ogden Spring 2018 UW Stout, Team S8-G4, Ogden Spring 2018人のメンバー

UWSTOUT-OGDEN-S18S8G4

4 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 14

今までの合計 1,083